User manual YAMAHA MC1204II MC1604II MC2404II MC3204II

[. . . ] Any notes being held by the sustain or sostenuto pedal will continue to sound until the pedal is released. (5) Omni Off (reception only) ccH Parameter Data Range (vvH) 7CH Omni Off 00H Same processing as for All Notes Off. (6) Omni On (reception only) ccH Parameter Data Range (vvH) 7DH Omni On 00H Same processing as for All Notes Off. [. . . ] (8) Poly (reception only) ccH Parameter Data Range (vvH) 7FH Poly 00H Same processing as for All Sound Off. · When Control Change is turned OFF, Control Change messages will not be transmitted or received. · Local on/off, OMNI on/off are not transmitted. (The appropriate note off number is supplied with "All Note Off" transmission). · When a voice bank MSB/LSB is received, the number is stored in the internal buffer regardless of the received order, then the stored value is used to select the appropriate voice when a program change message is received. This mode will not change when the instrument receives a MONO/POLY mode message. (3) Expression (reception only) ccH Parameter Data Range (vvH) 0BH Expression MSB 00H. . . 7FH (4) Sustain ccH Parameter 40H Sustain MSB (5) Sostenuto ccH Parameter 42H Sostenuto (6) Soft Pedal ccH Parameter 43H Soft Pedal Data Range (vvH) 00H. . . 7FH Data Range (vvH) 00H. . . 3FH:off, 40H. . . 7FH:on Data Range (vvH) 00H. . . 3FH:off, 40H. . . 7FH:on (7) Effect1 Depth (Reverb Send Level) ccH Parameter Data Range (vvH) 5BH Effect1 Depth 00H. . . 7FH Adjusts the reverb send level. (8) Effect4 Depth (Variation Effect Send Level) ccH Parameter Data Range (vvH) 5EH Effect4 Depth 00H. . . 7FH (9) RPN 65H RPN MSB 64H RPN LSB 06H Data Entry MSB 26H Data Entry LSB 60H Data Increment 61H Data Decrement * Parameters that are controllable with RPN: · Coarse Tune · Fine Tune · Pitch Bend Range 2 P-95 Data List / Daten-Liste / Liste des données / Lista de datos 4. PROGRAM CHANGE Data format: [CnH] -> [ppH] CnH = Program event (n = channel number) ppH = Program change number P. C. #=Program Change number Voice Name Grand Piano 1 Grand Piano 2 E. Piano 2 Jazz Organ Pipe Organ Strings Choir Harpsichord Vibraphone MSB 0 0 0 0 0 0 0 0 0 0 LSB 122 112 122 122 122 123 122 122 122 122 # P. C. # 1 1 6 5 17 20 49 53 7 12 7. SYSTEM EXCLUSIVE MESSAGES (Universal System Exclusive) (1) Universal Realtime Message Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] -> [llH] -> [mmH] -> [F7H] MIDI Master Volume · Simultaneously changes the volume of all channels. The message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent. (2) XG Native Bulk Data (reception only) Control Channel ccH vvH Channel Detune ch: 00H­0FH 43H (Sets the Detune value for each channel) 00H­7FH Voice Reserve ch: 00H­0FH 45H 00H : Reserve off 7FH : on* * When Volume, Expression is received for Reserve On, they will be effective from the next Key On. SYSTEM EXCLUSIVE MESSAGES (Others) Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H] -> [00H] -> [mmH] -> [llH] -> [ccH] -> [F7H] Master Tuning (XG and last message priority) simultaneously changes the pitch of all channels. F0H = Exclusive Status 43H = Yamaha ID 1nH = When received, n=0­F. 27H = Model ID of TG100 30H = Sub ID 00H = 00H = mmH = Master Tune MSB llH = Master Tune LSB ccH = irrelevant (under 7FH) F7H = End of Exclusive Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] -> [bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->. . . -> [ccH] -> [F7H] F0H = Exclusive status 43H = YAMAHA ID 0nH = When received, n=0­F. 4CH = Model ID of XG aaH = ByteCount bbH = ByteCount hhH = Address High mmH = Address Mid llH = Address Low ddH = Data | | | | ccH = Check sum F7H = End of Exclusive · Receipt of the XG SYSTEM ON message causes reinitialization of relevant parameters and Control Change values. Allow sufficient time for processing to execute (about 50 msec) before sending the NP-30/YNP-25 another message. · XG Native Parameter Change message may contain two or four bytes of parameter data (depending on the parameter size). · For information about the Address and Byte Count values, refer to Table 1 below. [. . . ] · For information about the Address and Byte Count values, refer to Table 1 below. Note that the table's Total Size value gives the size of a bulk block. Only the top address of the block (00H, 00H, 00H) is valid as a bulk data address. 9. [. . . ]