User manual YAMAHA MDX-793

[. . . ] U MDX-793 MINIDISC RECORDER LECTEUR ENREGISTREUR DE MINIDISC OWNER'S MANUAL MODE D'EMPLOI SAFETY INSTRUCTIONS 9 Heat -- The unit should be situated away from heat CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN sources such as radiators, stoves, or other units that produce heat. 10 Power Sources -- The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11 Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying attention to receptacles, and the point where they exit from the unit. 12 Cleaning -- The unit should be cleaned only as ÷ Explanation of Graphical Symbols recommended by the manufacturer. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 13 No Use Periods -- The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry -- Care should be taken so that objects do not fall into and liquids not spilled into the inside of the unit. 15 Damage Requiring Service -- The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. [. . . ] Turn the jog dial (or press SKIP $ or > on the remote) to select a track (recording starts from the beginning of the deleted track), or press * PAUSE during playback to pause at the point where you want to start recording. ! SKIP / REC 2 4 $ > PAUSE STOP TIME REC SYNC 6 & STOP PLAY < * & ? CD-P s MDX 14 4 Press REC to set this unit to record pause mode. The REC * indicators light up. "REC Standby" and the amount of time available for recording flash alternately in the display. If you selected a track number or paused playback (in step 3) to record over a previous recording "OverWriteOK?" appears in the display. This operation will erase the selected track number (or point) and all subsequent material. If you selected ANALOG in step 2, adjust the recording level as described in "Recording Level". Note When recording from a digital source that has a digital output (volume) control, set the output level (volume) to "MAX". Recording may not be possible at low output levels (when the digital volume is turned down). Recording Level To set the recording level, first set this unit to the record pause mode (press REC). Then play the loudest passage of the source to be recorded and watch the meter readings. Adjust the REC LEVEL control so that the highest peak causes the 0 dB level indicators to flicker. The OVER indicators should not light. L dB ­ 00 ­ 60 R ­30 ­10 ­6 4 ­ 2 ­1 0 OVER Should not light Note Although some sources can be recorded with lower peak levels, setting the peak levels too low may degrade the quality of the recording. 5 Start playing the program source to be recorded. 6 Press #/* (or # PLAY on the remote) to start recording. The TOC indicator lights up. When the TOC indicator is lit, this means that the TOC information has not yet been written to the disc. After recording, eject the disc, or turn this unit's power off to write the TOC information and finalize the recording. Auto Marking When making a recording, you can choose either automatic or manual marking. This feature operates somewhat differently for analog and digital signals. See below for details. To stop Press & (& STOP on the remote). To pause Press #/* (* PAUSE on the remote). To eject the MD Press ). Press M-MARK on the remote repeatedly to select automatic (MANUAL indicator out) or manual (MANUAL indicator lit) marking. MANUAL TOC writing may be impossible (or track number marking may not perform as expected) when recording a damaged CD or a broadcast source under interference. When recording analog signals Auto : Track numbers are written in synchronization with the input level of the signal being recorded. In other words, if the source signal falls below a certain level for more than 1. 5 seconds a track number is written automatically the next time the source signal rises above that level. Manual : One track number is written automatically when you start recording, but none are written during recording. To mark a track number, press REC at the desired position while recording. Note When using manual marking, the marks must be set at least 4 seconds apart. When recording digital signals Track numbers are written in the same positions as the original source (CD, etc. ) with either automatic or manual marking. To add additional track numbers, set M-MARK to MANUAL and press REC at the desired position while recording. [. . . ] UTOC WError Error occurred when writing to the UTOC. Not Audio The inserted disc is not an audio MD. Tr Protected The selected track cannot be edited because it is protected. TOC Full The disc area allotted for TOC data has become full and further editing is not possible. [. . . ]