User manual YAMAHA ME2000

[. . . ] (Pins are sharp and may cause hand cuts. ) G The ME2000 board is electrostatic-sensitive. Before handling the board, you should briefly touch the main unit's metal casing with your bare hand so as to drain off any static charge from your body. G Be sure to install the included lithium battery. This is a backup battery that is required maintain the data in the DM2000's expanded memory. ME2000 1 ESPAÑOL FRANÇAIS Precautions DEUTSCH ENGLISH FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. ENGLISH * * * * Please dispose of used batteries in accordance with local regulations. Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of the product. Company names and product names used herein are trademarks or registered trademarks of their respective owners. Use of the software and this manual is governed by the license agreement which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the important information and the Software Licensing Agreement of the Studio Manager's installation guide included with DM2000 before installing the software. ) Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. * ADVARSEL! Lithiumbatteri--Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. NEDERLAND G Dit apparaat bevat een lithium batterij voor geheugen back-up. G Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur afdankt of de volgende Yamaha Service Afdeiing: Yamaha Music Nederland Service Afdeiing Kanaalweg 18-G, 3526 KL UTRECHT Tel. 030-2828425 G Gooi de batterij niet weg, maar lever hem in als KCA. THE NETHERLANDS G This apparatus contains a lithium battery for memory back-up. G For the removal of the battery at the moment of the disposal at the end of the service life please consult your retailer or Yamaha Service Center as follows: Yamaha Music Nederland Service Center Address: Kanaalweg 18-G, 3526 KL UTRECHT Tel: 030-2828425 G Do not throw away the battery. Instead, hand it in as small chemical waste. 2 ME2000 G Note About Versions and Upgrades The ME2000 includes system version 1. 20 or higher, and is not compatible with pre-V1. 20 software. Before upgrading your DM2000 again in the future, be sure that your updater program is V1. 20 or higher. Studio Manager: The ME2000 is not compatible with Studio Manager versions prior to V1. 1. 1. If your version is older than V1. 1. 1, please replace it by installing the Studio Manager version included on the accompanying CD-ROM. For information about how to carry out the installation, refer to Studio Manager's installation guide. Note that Macintosh system requirements are now as indicated in the table below. [. . . ] Then remove the 4 screws holding the bridge in place (as shown below), and remove the bridge. 4. ENGLISH Remove the screws indicated in the illustration below: 10 screws from the left side, 10 screws from the right side, 8 screws from the front, and 7 screws from the rear. Loosen the axis screws slightly (but do not remove them), so that the control panel can pivot. Do not remove the axle screws. If these screws are removed the control panel may fall and cause injury or equipment damage. 5. <Rear View> Positioning Screw <Left Side View> Position- <Top View> ing Screw <Right Side View> 7 Screws Positioning Screw LCD 10 Screws 10 Screws Axis Screw <Front View> Axis Screw Positioning Screw 8 Screws 6. Hold onto the LCD, and lift up the rear of the control panel. LCD 7. Secure the raised control panel in place, so that it does not fall back down. ME2000 6 <Top View> CPU 5 Screws Lithium Battery Install the ME2000 Expansion Board and the Battery 1. Disconnect the 6 flat cables from the 4 white connectors and 2 black connectors on the CPU board. G To disconnect from white connectors: Pull out the connector latch as shown in the illustration, and then pull the cable out. [. . . ]