User manual YAMAHA MFC05

[. . . ] 2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functions du MFC05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Program change data and bank select data (BANK MSB/ LSB:off, 000-127) must be transmitted together to access these voices. Refer to the owner's manual of the receiving device for specific information on bank select data. · The default settings for each memory (001-128) is as follows. STATUS=C0 (Channel Number 1), DATA/CTRL=001-128 (same as the memory number), BANK MSB/MAX=off, BANK LSB/MIN=off. 10 Normal Mode How to Edit Memory If the FUNCTION lamp is lit, press [FUNCTION], so that the lamp is off, and Program Change Memory is enabled. 1Select the Memory Number to be edited (see page 9). Press [MEMORY EDIT] to edit to begin editing that Memory Number. (The lamp above that foot switch and the STATUS lamp will flash. ) MEMORY EDIT 2Press [MEMORY EDIT] to cycle through the 4 edit parameters (the selected parameter's light will flash). · TOGGLE ON-OFF/NUMBER OF PGM can not be selected from Program Change Memory. MEMORY EDIT STATUS settings STATUS DATA/CONTROL settings DATA/CTRL BANK MSB/MAX BANK MSB settings BANK LSB settings BANK LSB/MIN TOGGLE ON-OFF /NUMBER OF PGM 3Use [INC/YES] and [DEC/NO] to edit the parameter. Press [INC/YES] to increase the value shown in the LED display by 1, press [DEC/NO] to decrease the value by 1. By holding a button, values will continuously increase or decrease. Hold the [INC/YES] button and press the [DEC/NO] button and the value shown in the LED display will increase by 10. Repeatedly press [DEC/NO] to continue increasing the value by 10. Hold the [DEC/NO] button and press the [INC/YES] button and the value shown in the LED display will decrease by 10. Repeatedly press [INC/YES] to continue decreasing the value by 10. 001 DEC ±10 INC /NO /YES 128 128 DEC ±10 INC /NO /YES 001 DEC ±10 INC /NO /YES Increase by 10 Decrease by 10 DEC ±10 INC /NO /YES 4After the desired parameters have been edited in steps 2 and 3, press [WRITE/EXIT]. By holding a button, values will continuously increase or decrease. Hold the [INC/YES] button and press the [DEC/NO] button and the value shown in the LED display will increase by 10. Repeatedly press [DEC/NO] to continue increasing the value by 10. Hold the [DEC/NO] button and press the [INC/YES] button and the value shown in the LED display will decrease by 10. Repeatedly press [INC/YES] to continue decreasing the value by 10. 001 DEC ±10 INC /NO /YES 128 128 DEC ±10 INC /NO /YES 001 Increase by 10 DEC ±10 INC /NO /YES Decrease by 10 DEC ±10 INC /NO /YES 5After the desired parameters have been edited in steps 3 and 4, press [WRITE/EXIT]. The Memory Number shown in the LED display will flash. · If data has not been edited, the Memory Number will not flash and the MFC05 will return to its normal control mode. WRITE /EXIT F07 6Press [INC/YES], to save the edited data to the current Memory Number, The MFC05 will return to its normal control mode. Press [DEC/NO] to cancel the save operation of the edited data. At this time the memory will revert to its pre-edited condition. DEC ±10 INC /NO /YES DEC ±10 INC /NO /YES · Another Memory Number from the same bank (10's digit bank) can be easily edited by pressing [1] - [0] without exiting from the edit mode. You must execute or cancel the save operation for the currently edited data (the current Memory Number will flash) before proceeding to edit the new number. Use [INC/ YES] to execute or [DEC/NO] to cancel the save operation. If data has not been edited, the Memory Number will not flash and the newly selected Memory Number will be shown in the display. 17 Normal Mode About the TOGGLE ON-OFF/NUMBER OF PGM settings. TOGGLE ON-OFF/NUMBER OF PGM contains the settings for "on, off, Pn1, Pn2, Pn3, Pn4". [. . . ] ­>Reduce the volume of data being transmitted or transmit the data in smaller blocks. If "Er5" appear again, Memory Data Error. An error has occurred in the internal memory. ­>Take the device to your nearest Yamaha dealer for further evaluation. Er2 Er3 Er4 Er5 Trouble Shooting Problem Program changes do not transmit. [. . . ]