User manual YAMAHA MG06X/MG06

[. . . ] ZG13410 EN GAIN MIXING CONSOLE Equalizer Mixer Basics: Where Your Sound Goes The right illustration diagram illustrates the sound flow from summing (mixing) sound which was input to the channels to outputting sound from the speakers or headphones. Let’s find out where input sound goes once it’s inside the mixer. 1 Input the sound from a microphone or instrument 5 Output the sound from speakers or headphones Owner’s Manual Welcome Thank you for purchasing the Yamaha MG06X/MG06 Mixing Console. Please read this manual thoroughly to get the most out of the product and ensure long-term, trouble-free use. After reading this manual, keep it readily available for future reference. [. . . ] • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. Location • Do not place the device in an unstable position where it might accidentally fall over. • Do not place the device in a location where it may come into contact with corrosive gases or salt air. • Before moving the device, remove all connected cables. • When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn the power off and disconnect the plug from the outlet. Even when the power is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. Sound is faint, distorted, or noisy. Are □□ the [GAIN] knobs and [LEVEL] knobs of all relevant channels, and the [STEREO LEVEL] knob set too high?Lower the [GAIN] knobs of channels 1/L and 2/R, or turn on (O) the [PAD] switches. Are □□ the “PEAK” (red) lamps of the level meter lit?Set the [LEVEL] knobs of all relevant channels and the [STEREO LEVEL] knob to appropriate levels. Are □□ the [PAD] switches turned off (N)?If the volume of sound source is too loud, turning off the switches may result in distorted sound. Is □□ the volume from the connected device too loud?Lower the volume of the connected device. *1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter. Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corporation reserves the right to modify products or specifications at any time without prior notice. Since specifications, equipment, and options may not be the same in every locale, please check with your Yamaha dealer. Connections • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. (class b korea) OBSERVERA!Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av. ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt — også selvom der er slukket på apparatets afbryder. VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta. (standby) Jack List (Pin Alignment) Input and Output Jacks Polarities Pin 1: Ground Pin 2: Hot (+) Pin 3: Cold (-) Tip: Hot (+) Ring: Cold (-) Sleeve: Ground Tip: L Ring: R Sleeve: Ground Balanced/Unbalanced Configurations Do not open • This device contains no user-serviceable parts. [. . . ] If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out. To yy avoid generating unwanted noise, make sure there is adequate distance between the AC power adaptor and the device. Avoid setting all equalizer and level knobs to their maximum. Depending on the condition of the connected devices, doing yy so may cause feedback and may damage the speakers. [. . . ]