User manual YAMAHA MLAN8

[. . . ] mLAN EXPANSION BOARD Owner's manual Bedienungsanleitung Mode d'emploi Français Deutsch mLAN8E English FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. [. . . ] They cannot be saved on disk. Cursor 1 Out (output) s Knob 1 [ turn] Move cursor / switch pages Move the cursor or switch pages. [ press] Tree View Access the Tree View screen. s Knob 2 [ turn] Out (select output plug) Select the mLAN plug of the mLAN8E that will be the output source. u Setting: AS (assignable) 1~6, DIG-L, DIG-R, MIDI 10 Settings on the device in which the mLAN8E is installed s Knob 3 [ turn] Connect# (select connection number of the connected mLAN device) Select the connection number of the connected mLAN device. In the case of numbers for which a connection has already been made, the module name and plug name will be displayed in parentheses. The Word Clock Mode will be "Auto. " NOTE The Nickname settings will not be initialized. s Knob 4 [ turn] Select connected module Select an mLAN device on the mLAN bus (system). When you select a valid mLAN device, the top line will show the vendor name and the Nickname. s Knob 5 [ turn] Select connected mLAN plug Select an mLAN output plug on the connected mLAN device. NOTE The connection is executed by CONNECT (press knob 5). If after making your selection, you change pages, move the cursor, or change the Out or Connect# settings without executing CONNECT, the selected value will be cleared. If there are no plugs that can be selected, this will be displayed as "---. " NOTE [ press] CONNECT Connect to the mLAN output plug of the selected mLAN device. If the node number is "New, " this function will appear if you have selected a module name or plug name that can be connected. [ press] CUT (disconnect) Break the selected connection. This function will appear if you have selected an already-connected module name or plug name. 12 Settings on the device in which the mLAN8E is installed mLAN Cnfg (mLAN configuration) NOTE Output Level Offset, Word Clock Mode, and Nickname settings are saved in the mLAN8E. They cannot be saved on disk. Cursor 1 s Knob 1 [ turn] Move cursor / switch pages Move the cursor or switch pages. [ press] Tree View Access the Tree View screen. s Knob 2 [ turn] Output Level Offset Specify the output volume (offset value) for all mLAN audio outputs. u Setting: +0 dB ~ +24 dB s Knob 4 [ turn] Audio Input (audio input select) Select the audio input source. u Setting ADIn: mLAN: Use two analog audio channels from the INPUT jacks of the A5000/A4000. The audio signals from the INPUT jacks of the A5000/ A4000 will not be input. Cursor 2 s Knob 1 [ turn] Move cursor / switch pages Move the cursor or switch pages. [ press] Tree View Access the Tree View screen. s Knob 3 [ turn] Word Clock Mode Specify the word clock. u Setting Auto: The word clock of the audio output will automatically synchronize to an 44. 1 kHz external device. The A5000/A4000 may function as the master in some cases, or as the slave in other cases. Group1Master (44. 1 kHz): The A5000/A4000 will function as a 44. 1 kHz master device. 13 English Settings on the device in which the mLAN8E is installed Before the Word Clock Mode is selected or after SET is executed, this will indicate the current Word Clock Mode. The display has the following significance. · · · · Auto(Int): Operating in Auto Mode on the internal clock Auto(Ext): Operating in Auto Mode as a slave ---(Int): Operating in Manual Mode on the internal clock ---(Ext): Operating in Manual mode as a slave English [ press] SET (finalize word clock) Finalize the selected Word Clock Mode setting. s Knob 4 Nickname (display only) Displays the Nickname of the A5000/A4000. [ press] Rename Set the Nickname. s Knob 5 [ turn] MIDI Input (MIDI Input selection) NOTE Regardless of this setting, the same MIDI output data is sent from both MIDI OUT and mLAN MIDI. Regardless of this setting, the MIDI THRU connector will re-transmit the data that was input to MIDI IN. NOTE u Setting MIDI IN: MIDI messages input from the MIDI IN connectors will play the A5000/A4000; mLAN will not be used. mLAN->A: MIDI messages from the mLAN MIDI input will be sent to the MIDI IN-A port. MIDI messages from the rear panel MIDI IN-A connector will not be input (A5000 only). mLAN->B: MIDI messages from the mLAN MIDI input will be sent to the MIDI IN-B port. [. . . ] It cannot be saved on a memory card. 19 English (1) Turn knob [A] to select the mLAN8E mLAN plug that will input the signal. The module name and plug name for the destination device will be displayed as "-----". Settings on the device in which the mLAN8E is installed mLAN initialize This initializes the mLAN connection and word clock settings of the mLAN8E installed in the CS6x/CS6R/S80. When you press [ENTER], a confirmation screen will appear. Press [YES] to execute the initialization, or press [NO] to cancel. English mLAN Initialize) Sys [ENTER] to Init NOTE The Nickname settings will not be initialized. mLAN Nickname Specify the nickname of the CS6x/CS6R/S80 in which the mLAN8E is installed. [. . . ]