User manual YAMAHA MSP10STUDIO

[. . . ] Liquid or metal objects inside this unit are a fire and electrical shock hazard. · If there is a possibility of lightning, do not touch the power cable plug if it is still connected. Doing so may be an electrical shock hazard. Doing so is a fire and electrical shock hazard. · Do not remove the unit's cover. [. . . ] If the airflow is not adequate, the unit will heat up inside and may cause a fire. Operation · Turn off all musical instruments, and audio equipment when connecting to this unit. Use the correct connecting cables and connect as specified. · Always lower the volume control to minimum before turning on the power to this unit. A sudden blast of sound may damage your hearing. · Do not output distorted sounds for long periods of time, as this will cause the speaker to heat up, leading to a fire hazard. · Do not raise the volume of headphones or speakers to a level that makes you feel uncomfortable. Listening to loud music for long periods can damage your hearing. · If you know you will not use this unit for a long period of time, such as when going on vacation, remove the power plug from the AC outlet. Leaving it connected is a potential fire hazard. Maintenance · To prevent electrical shock when cleaning the unit, remove the power plug from the AC outlet. PRECAUTIONS Connector pin assignments ­ for correct operation ­ Operation · This speaker is magnetic shielded. However, if a nearby monitor displays any uneven colors, place it further away from the monitor. · You may feel a flow of air in and out of the port on this unit. This is not abnormal and sometimes occurs when a program with a lot of bass range is played. · XLR-type connectors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (­). Influence on cell phone usage · Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from the unit. WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN-AND-YELLOW : BLUE : BROWN : EARTH NEUTRAL LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. * This applies only to products distributed by YAMAHA KEMBLE MUSIC (U. K. ) LTD. 4 Front panel/Rear panel 2 3 4 5 2 3 1 1 ON OFF POWER 6 2 TRIM switches 1 Power/Clip indicator This indicator lights up green when you turn ON the POWER switch on the rear panel. If the output level is too high, causing clipping at the amplifier, the indicator lights up red. These switches enable you to adjust the bass and treble for the MSP10STUDIO. LOW: three positions The LOW switch adjusts the bass range. At a frequency of 50 Hz, changing the setting from "0" to "­1. 5" will cut the bass range by 1. 5 dB. Changing the setting from "0" to "­3" will cut the bass range by 3 dB. HIGH: three positions The HIGH switch adjusts the treble. [. . . ] For European Model Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 11A Conformed Environment: E1, E2, E3 and E4 Dimensions Performance graph Standard frequency response +10 0 H: 420 RESPONSE (dB) 85 5. 5 262 D: 329 61. 5 ­10 ­20 ­30 120 W: 265 2-M8 Screws ­40 20 100 1k 10k Unit: mm FREQUENCY (Hz) 6 Block Diagram HPF INPUT SENSITIVITY EQ LOW CUT 0 ­1. 5 +1. 5 0 LPF HPF ­1. 5 ­3 LOW HIGH TRIM Mounting the MSP10STUDIO on the wall You can install the MSP10STUDIO on the wall using an optional Yamaha wall bracket BWS251-300. For more information on how to install it, refer to the instructions that come with the wall bracket. For the angle and position of installation, refer to the figure below. [. . . ]