User manual YAMAHA MSP7STUDIO

[. . . ] MSPs MSP7 STUDIO MSP5 STUDIO Powered Subwoofer eries Powered Monitor Speaker SW10 STUDIO Powered Near-field Reference Monitors & Subwoofer OWNER'S MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE INSTRUCCIONES EN DE FR ES ZH JA Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the rear of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read these instructions. Install in accordance with the manufacturer's instructions. [. . . ] It's also important to be aware of the location of doors and windows. It is not always possible to achieve ideal symmetry, but it's worth getting as close as possible. MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner's Manual The "Sweet Spot" For both stereo and surround mixing your position in relation to the main front speakers -- the "sweet spot" as it's often called -- should be one apex of an equilateral triangle. In other words your distance from either speaker should be the same as the distance between the two speakers. The speakers should also be "toed in" to the corresponding 60 angle so that the drivers are aimed directly at the listening position. The height of the speakers should be such that the tweeters are roughly aligned with your ears (this is because high frequencies are the most directional). 60 Fine-tuning for Stereo (MSP7 STUDIO or MSP5 STUDIO x 2) The speaker LEVEL controls should be set to the same level. A setting of about 12 o'clock corresponds to a nominal input level. Since no subwoofer is being used in this setup, if your speakers have a LOW CUT switch, set it to "FLAT" (the MSP7 STUDIO has a LOW CUT switch). For accurate monitoring set the LOW TRIM switch to "0". If you want to reduce the low-frequency level a bit set the switch to "-1. 5". For accurate monitoring set the HIGH TRIM switch to "0". This switch can be set to "-1. 5 dB" to attenuate the highs slightly if you find the sound too bright. MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner's Manual 7 English Adding a Subwoofer English 8 Even if you don't plan to set up a surround system, adding a subwoofer can be a real advantage for stereo mixing. If you can't hear the extreme low end there's not much you can do to make it sound great. The extended bass response provided by a good subwoofer can indeed help you to improve the overall quality of your mixes. The location of your subwoofer is not as critical as the main speakers, because frequencies below around 200 Hz -- the region your subwoofer will be working in -- aren't directional. To say it another way, the ear can't locate the source of such low frequencies, so in theory the subwoofer can be placed anywhere in the room. In reality it's a good idea to place the subwoofer on the floor somewhere between the main front speakers at the same distance from the listening position as the main speakers, but it doesn't have to be dead center. Fine-tuning for Stereo + Subwoofer (MSP7 STUDIO or MSP5 STUDIO x 2, SW10 STUDIO x 1) Set the MSP7 STUDIO or MSP5 STUDIO LEVEL control to about 12 o'clock for nominal input level. If you're using the MSP7 STUDIO set the SW10 STUDIO LEVEL control to about 12 o'clock, and if you're using the MSP5 STUDIO set it to about 10 o'clock. You can then fine-adjust the SW10 STUDIO LEVEL control as required. Another approach would be to adjust the MSP7 STUDIO/MSP5 STUDIO output level to achieve the desired relative balance with the subwoofer. Start with the SW10 STUDIO HIGH CUT control set at its center click position, which corresponds to a HPF frequency of about 80 Hz. The HIGH CUT frequency can be adjusted later to achieve the smoothest integration with the MSP7 STUDIO or MSP5 STUDIO speakers. If you are using the MSP7 STUDIO, set the LOW CUT switch to "80". [. . . ] 120Hz 80Hz 40Hz MSP7 STUDIO STEP FILTER LOW CUT P. AMP HF LOW CUT LOW CUT TRIM INPUT LEVEL FLAT 80Hz 100Hz LOW HIGH HIGH CUT P. AMP LF MSP5 STUDIO LOW CUT P. AMP HF 1 LOW CUT TRIM INPUT LEVEL 2 HIGH CUT P. AMP LF SW10 STUDIO INPUT L OUTPUT P. AMP HIGH CUT INPUT LEVEL INVERTER INVERTER P. AMP SPEAKER PHASE SW EQ HIGH CUT R OUTPUT INPUT SUBWOOFER OUTPUT 67 Espaol Franais Block Diagram Deutsch -40 English For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA Yamaha Music Central Europe GmbH, Branch Austria, CEE Department Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 OTHER COUNTRIES Yamaha Music Gulf FZE LB21-128 Jebel Ali Freezone P. O. Box 17328, Dubai, U. A. E. Tel: +971-4-881-5868 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]