User manual YAMAHA MTX3

[. . . ] Owner’s Manual EN Contents Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Included items (please check) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Firmware versions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Precautions for rackmounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Introducing the MTX3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make DCP settings. Assign the parameters of the MTX3 to the switches and knobs of the connected DCP units. Here you can also specify the brightness of the DCP’s LEDs. On-site work (Installation and wiring) Install and connect the system while referring to the schematic diagram you printed out. 9. Specify and store a preset. You can use presets to change the volume of zones and the audio source to play (e. g. , SD memory card or CD player) in a single action. To prevent problems such as a sudden increase in volume when the MTX3 is operated, we recommend that you store the preset with the output level lowered to “-infinity (). ” For details on presets and how to recall them, refer to “Recalling (switching) presets” on page 16, and “MTX Editor User’s Manual. ” 1. Install the MTX3, and make the analog audio connections. Make digital connections between the MTX3 and any XMV. Make a ring connection between the MTX3 and the other devices equipped with a [YDIF] connector, such as an XMV series amplifier. 10. Save your settings and close MTX Editor. A project file with the extension “. mtx” will be created. 3. Connect the MTX3 to an analog input amp (other than XMV). Set the UNIT ID of the MTX3 and the XMV. Set the UNIT ID for every MTX3 and XMV device you connected in the above steps. The UNIT ID is specified by the combination of the [UNIT ID] rotary switch and DIP switches located on each device’s rear panel. Set each device to a different UNIT ID so that no conflict occurs. 5. Make connections between the MTX3 and the DCP units. Daisy-chain the DCP units. Set the panel ID and termination settings of the DCP units. For details, refer to the DCP owner’s manual. 14 MTX3 Owner’s Manual Quick Guide On-site work (Settings in MTX Editor) Use MTX Editor to make adjustments for the entire system. 10. Place the XMV and MTX Editor online. When they go online, the amp will be detected and you will be able use MTX Editor to control the XMV. MTX Editor will detect the devices that are connected on the network, and will put the detected devices online. 1. Connect the MTX3 to the computer. Connect the computer to the MTX3 directly or via a network switch. 2. Start up MTX Editor and load the project file that you previously created. Go the MTX3 and MTX Editor online (in a synchronized state). “Online” refers to the state in which the MTX3 itself is connected with MTX Editor and is synchronized. For details on how to put the device online, refer to “MTX Editor User’s Manual. ” 11. Adjust the output level of the MTX3 and the output level of the amps so that the audio is output at an appropriate level. One by one, turn on each output channel and adjust its output level. 12. Store the preset. As necessary, recall a preset that includes output, specify the output level, and save the preset. [. . . ] Tel: 714-522-9011 MALTA Olimpus Music Ltd. Louis Street Msida MSD06 Tel: 02133-2144 ASIA THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 Yamaha Music India Pvt. Spazedge building, Ground Floor, Tower A, Sector 47, Gurgaon- Sohna Road, Gurgaon, Haryana, India Tel: 0124-485-3300 PT. [. . . ]