User manual YAMAHA MU100E2

[. . . ] TONE GENERATOR SOUND LIST & MIDI DATA TABLE OF CONTENTS EFFECT A/D Input Preset Effect Type List Effect LSB/MSB List Effect Parameter List Effect Data Assign Table MIDI MIDI data format MIDI implementation chart VOICE XG Voice List TG300B Voice List About the 128 GM sounds C/M Voice List XG Drum Map TG300B Drum Map C/M Drum Map Performance List 4 5 8 11 25 28 60 62 90 98 100 101 106 107 108 3 A/D Input Preset A/D Input Preset BANK Source 0 MIC Preset Name input gain var type 1 GUITAR Preset Name (Note 1) input gain var type 2 KEYBOARD Preset Name input gain var type 3 AUDIO Preset Name (Note 2) input gain var type 18 STEREO Preset Name KEYBOARD input gain (Note 3) var type 19 STEREO Preset Name AUDIO input gain (Note 3) var type A/D1 A/D2 PGM # = 1 Off mic Off mic Off line Off line Off line Off line 2 Mic mic Guitar mic Keyboard line Audio line Keyboard line Audio line 3 4 Reverb Chorus mic mic Reverb Chorus mic mic Reverb Chorus line line Reverb Chorus line line Reverb Chorus line line Reverb Chorus line line 5 Chorus+Reverb mic Chorus+Reverb mic Chorus+Reverb line Chorus+Reverb line Chorus+Reverb line Chorus+Reverb line 6 Karaoke1 mic Karaoke1 Tube mic Amp Sim. Phaser EP line Phaser 7 8 Karaoke2 Karaoke3 mic mic Karaoke2 Karaoke3 Stack Flang Gtr mic mic Amp Sim. Flanger Pan EP Wah Clavi line line Auto Pan Touch Wah 9 Echo mic Echo Clean Gtr mic Celeste Rotary Orgn line Rotary Speaker 10 Vocal mic Stage1 Funk Gtr mic Touch Wah Synth Str line Symphonic 11 Studio mic Exciter Tremolo mic Tremolo Synth Pad line Flanger2 12 Oct Up mic Pitch Change Phaser mic Phaser Synth Lead line Delay LCR 13 Oct Down mic Pitch Change 5th Guitar mic Pitch Change SFX line Pitch Change Phaser EP Pan EP Wah Clavi Rotary Orgn Synth Str Synth Pad Synth Lead SFX line line line line line line line line Phaser Auto Pan Touch Wah Rotary Speaker Symphonic Flanger2 Delay LCR Pitch Change (Note 1) Depending on the guitar, the input may be distorted. Adjust the A/D INPUT VOLUME or the volume of your guitar. [. . . ] No effect if Bank Select MSB=127 is selected. *4 No effect if Multi Part parameter PART MODE = DRUM, DRUMS1. . . 4. 1. 2. 22 RPN (Registered parameter number) This message is used to specify part parameters such as Pitch Bend Sensitivity or Tuning etc. Use RPN MSB and RPN LSB to specify the parameter that you wish to modify, and then use Data Entry (see 1. 2. 4) to set the value of the specified parameter. Control# 100 101 Parameter RPN LSB RPN MSB Data Range 0. . . 127 0. . . 127 1. 3 Channel mode messages These messages specify the basic operation of a part. 1. 3. 1 If the Multi Part parameter Rcv RPN = OFF, that part will not receive this message. The following RPN messages can be received. All Sound Off This message silences all currently-sounding notes on the corresponding channel. However, the state of channel messages such as Note-on and Hold-on will be maintained. 32 MU100 MIDI MIDI data format Control# 120 Parameter All Sound Off Data Range 0 1. 3. 6 Mono 1. 3. 2 Reset All Controllers Perform the same processing as when All Sound Off is received, and if the value (mono number) is in the range of 0. . . 16, set the corresponding channel to Mode4* (m = 1). Control# 126 Parameter Mono Data Range 0. . . 16 This message resets the following controllers to their default values. Controller Pitch bend change Channel pressure Polyphonic key pressure Modulation Expression Hold Portamento Sostenuto Soft pedal Portamento control RPN NRPN Value ±0 (center) 0 (off) 0 (off) 0 (off) 127 (maximum) 0 (off) 0 (off) 0 (off) 0 (off) Reset the portamento source note number that was received Number unset, internal data is not affected. Number unset, internal data is not affected. * Mode4 is a state in which only channel messages on the specified channel will be received, and notes will be sounded individually (monophonically). 1. 3. 7 Poly Perform the same processing as when All Sound Off is received, and set the corresponding channel to Mode3*. Control# 127 Parameter Poly Data Range 0 * Mode3 is when channel messages will be received only on the specified channel, and will be sounded polyphonically. 1. 4 Program change The following data is not changed Parameter values specified by program change, bank select MSB/LSB, volume, pan, effect send levels 1, 3, 4, RPN and NRPN. Control# 121 Parameter Reset All Controllers Data Range 0 This message is used to select voices or performances. When this is transmitted in conjunction with Bank Select (see 1. 2. 1), voices and performances can be selected not only from the basic voice bank but also from the extended voice bank and from internal performances. If the Multi Part parameter Rcv PROGRAM CHANGE = OFF, that part will not receive program changes. If Sound Module Mode = C/M, program changes for the Drum Part will not be received. 1. 3. 3 All Note Off This message turns off all notes which are currently on for the corresponding part. However, if Hold 1 or Sostenuto are on, notes will continue to sound until these are turned off. Control# 123 Parameter All Note Off Data Range 0 1. 5 Pitch bend This message conveys movements of the pitch bender. This message is generally used to modify the pitch of a part, but the depth of the following seven effects can be controlled. The effect of this message can be modified by the following parameters. BEND LFO AMOD DEPTH · Effect1 Parameter 7. BEND VARIATION CONTROL DEPTH (Valid when Variation Effect is assigned to a part as Insertion) By default, the Pitch Control effect is applied. If the receive channel is a drum part, effects 5 and 6 will not apply. If the Multi Part parameter Rcv PITCH BEND CHANGE = OFF, that part will not receive pitch bend messages. 1. 3. 4 Omni Off Perform the same processing as when All Note Off is received. [. . . ] An effect sound that takes advantage of portamento. Raise MW to make the sound change even more. Split sound with soft-feeling guitar and breathy tenor sax. Layered DX electric piano and acoustic guitar. [. . . ]