User manual YAMAHA MU128E2

[. . . ] SOUND LIST & MIDI DATA TABLE OF CONTENTS A/D Input Preset Effect Type List Effect LSB/MSB List Effect Parameter List Explanation of effect parameters Effect Data Assign Table MIDI MIDI implementation chart VOICE XG Voice List TG300B Voice About the 128 GM sounds XG Drum Map TG300B Drum Map Performance List 62 90 102 104 109 110 60 4 5 8 11 25 23 3 VOICE MIDI data format 28 MIDI EFFECT EFFECT A/D Input Preset A/D Input Preset BANK Source 0 MIC Preset Name input gain var type 1 GUITAR Preset Name (Note 1) input gain var type 2 KEYBOARD Preset Name input gain var type 3 AUDIO Preset Name (Note 2) input gain var type 18 STEREO Preset Name KEYBOARD input gain (Note 3) var type 19 STEREO Preset Name AUDIO input gain (Note 3) var type A/D1 A/D2 PGM# = 1 Off mic Off mic Off line Off line Off line Off line 2 Mic mic Guitar mic Keyboard line Audio line Keyboard line Audio line 3 4 Reverb Chorus mic mic Reverb Chorus mic mic Reverb Chorus line line Reverb Chorus line line Reverb Chorus line line Reverb Chorus line line 5 Chorus+Reverb mic Chorus+Reverb mic Chorus+Reverb line Chorus+Reverb line Chorus+Reverb line Chorus+Reverb line 6 Karaoke1 mic Karaoke1 Tube mic Amp Sim. Phaser EP line Phaser 7 8 Karaoke2 Karaoke3 mic mic Karaoke2 Karaoke3 Stack Flang Gtr mic mic Amp Sim. Flanger Pan EP Wah Clavi line line Auto Pan Touch Wah 9 Echo mic Echo Clean Gtr mic Celeste Rotary Orgn line Rotary Speaker 10 Vocal mic Stage1 Funk Gtr mic Touch Wah Synth Str line Symphonic 11 Studio mic HM Enhancer Tremolo mic Tremolo Synth Pad line Flanger2 12 Oct Up mic Pitch Change Phaser mic Phaser Synth Lead line Delay LCR 13 Oct Down mic Pitch Change 5th Guitar mic Pitch Change SFX line Pitch Change EFFECT 4 Phaser EP Pan EP Wah Clavi Rotary Orgn Synth Str Synth Pad Synth Lead SFX line line line line line line line line Phaser Auto Pan Touch Wah Rotary Speaker Symphonic Flanger2 Delay LCR Pitch Change (Note 1) Depending on the guitar, the input may be distorted. Adjust the A/D INPUT VOLUME or the volume of your guitar. [. . . ] Control# 96 97 Parameter RPN Increment RPN Decrement Data Range --01 53 mm -- *4 01 99 mm -- The data byte is ignored. 1. 2. 21 NRPN (Non-registered parameter number) This message is used to specify a sound parameter (such as vibrato, filter, EG, drum setup etc. ) as an offset value. Use NRPN MSB and NRPN LSB to specify the parameter that you wish to modify, and then use Data Entry (see 1. 2. 4) to set the value for the specified parameter. 01 100 mm -- 01 102 mm -- 30 MU128 MIDI MIDI data format 20 rr mm -Drum low pass filter cutoff frequency rr: drum instrument note number mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum low pass filter resonance rr: drum instrument note number mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum EG attack rate rr: drum instrument note number mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum EG decay rate rr: drum instrument note number mm: 00 - 64 - 127 (-64. . . 0. . . +63) The effect will apply both to Decay 1 and 2. Drum instrument pitch coarse rr: drum instrument note number mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum instrument pitch fine rr: drum instrument note number mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum instrument level rr: drum instrument note number mm: 00 - 127(0. . . maximum) Drum instrument panpot rr: drum instrument note number mm: 00, 01-64-127(RND, L63. . . C. . . R63) Drum instrument reverb send level rr: drum instrument note number mm: 00 - 127(0. . . maximum) Drum instrument chorus send level rr: drum instrument note number mm: 00 - 127(0. . . maximum) Drum instrument variation send level rr: drum instrument note number mm: 00 - 127(0. . . maximum) (when Variation Connection = SYSTEM)) mm: 00, 01-127 (OFF, ON) (when Variation Connection = INSERTION)) 36 rr mm -Drum high pass filter cutoff frequency mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum EQ bass gain mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum EQ treble gain mm: 00 - 64 - 127 (-64. . . 0. . . +63) Drum EQ bass frequency mm: 04 - 40(32. . . 2. 0k [Hz]) Drum EQ treble frequency mm: 28 - 58(500. . . 16. 0k [Hz]) 48 21 rr mm -- rr mm -- 49 rr mm -- 22 rr mm -- 52 rr mm -- 23 rr mm -- 53 rr mm -- MSB 14H-35H (for drums) is received when Multi Part parameter PART MODE = DRUMS1. . . 4. *1 Refer to 1. 2. 4 *2 '--' indicates that the setting value is ignored. *3 Adjusts the time after the note is played until vibrato begins to take effect. The effect will begin more quickly for higher values, and more slowly for higher values. No effect if Bank Select MSB=127 is selected. *4 No effect if Multi Part parameter PART MODE = DRUM, DRUMS1. . . 4. 24 rr mm -- 25 rr mm -- 26 rr mm -- 1. 2. 22 RPN (Registered parameter number) This message is used to specify part parameters such as Pitch Bend Sensitivity or Tuning etc. Use RPN MSB and RPN LSB to specify the parameter that you wish to modify, and then use Data Entry (see 1. 2. 4) to set the value of the specified parameter. Control# 100 101 Parameter RPN LSB RPN MSB Data Range 0. . . 127 0. . . 127 28 rr mm -- 29 rr mm -- If the Multi Part parameter Rcv RPN = OFF, that part will not receive this message. The following RPN messages can be received. RPN MSB LSB 00 00 Data Entry*1 MSB LSB mm -- *2 30 rr mm -- Parameter name and value range Pitch bend sensitivity mm: 00-24 (0. . . +24 semitones) Specify up to 2 octaves in semitone steps Fine tuning mm ll: 00 00 : mm ll: 64 00 : mm ll: 127 127 31 rr mm -- 00 01 mm ll -100 cents : 0 cents : +100 cents MU128 MIDI 31 MIDI data format [Note] mm ll: 00 127 (=-87. 5) cents is followed by 01 00 (=-87. 4) cents. Controller Pitch bend change Channel pressure Polyphonic key pressure Modulation Expression Hold Portamento Sostenuto Soft pedal Portamento control RPN *1 Refer to 1. 2. 4 *2 '--' indicates that the setting value is ignored. NRPN Value ±0 (center) 0 (off) 0 (off) 0 (off) 127 (maximum) 0 (off) 0 (off) 0 (off) 0 (off) Reset the portamento source note number that was received Number unset, internal data is not affected. Number unset, internal data is not affected. 00 02 mm -- Coarse tuning mm: 40 - 64 - 88 (-24. . . 0. . . +24 semitones) RPN Null This sets RPN and NRPN numbers to an unset state. Internal data is not affected. 127 127 -- -- 1. 2. 23 Assignable controller By assigning a control change number of 0. . . 95 to a part, the specified effect can be controlled. This device allows two control change numbers (AC1 and AC2) to be specified for each part. The following parameters specify the effect of AC1 and AC2. AC1, AC2 LFO AMOD DEPTH · Effect1 Parameter 7. AC1, AC2 VARIATION CONTROL DEPTH (Valid if Variation Effect is assigned to a part as Insertion) · Effect 2 Parameter 8. AC1, AC2 INSERTION CONTROL DEPTH The AC1 control change number is specified by the Multi Part or A/D Part parameter AC1 CONTROLLER NUMBER, and the AC2 control change number is specified by the Multi Part or A/D Part parameter AC2 CONTROLLER NUMBER. [. . . ] Analog brass with strong sense of attack. Synth lead in which velocity creates unique tonal change in the attack. Soft-attack synth sound with a feel of sweep. Synth sound in which the filter changes slowly. [. . . ]