User manual YAMAHA MV1000

[. . . ] This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. [. . . ] · TAPE IN jacks and REC OUT jacks offer easy connection of tape decks for playback and recording. Contents Front & Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Channel Control Section . . . . . . . . . . . . . . . . . . . . . . . . 3 Master Control Section . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About the Accessories . . . . . . . . . . . . . . . . . . . . . . 11 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Supplement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Block and Level Diagrams . . . . . . . . . . . . . . . . . . . . 17 Caution: When the unit is installed in a rack The main unit's power switch is located on the rear panel of the unit. · LINE: Compatible with 600 line level devices. w ST INPUT Jacks (CH 9-12) Both unbalanced RCA phono type stereo line input jacks and unbalanced Euro-block connectors are supplied. Both types are compatible with 600 line level devices. e INSERT IN Jacks (CH 1-4) r INSERT OUT Jacks (CH 1-4) These are input/output jacks that are positioned between the equalizer and fader of the Input Channel. The INSERT IN jacks are balanced phone type jacks with a nominal input/impedance of 0dB/600. The INSERT OUT jacks are impedance balanced phone type jacks with a nominal output/impedance of 0dB/10k. These jacks can be used to connect a graphic equalizer, compressor, noise filter, etc. MV12/6 -- Owner's Manual 8 Front & Rear Panels t SEND Jacks · AUX1, AUX2 These are impedance balanced phone type output jacks with a nominal output/impedance of +4dB/ 600. The AUX1, 2 bus signals are output from their respective jacks. These jacks can be used to send the signal to monitor system such as a cue-box. · EFFECT This is an impedance balanced phone type output jack with a nominal output/impedance of +4dB/ 600. The signal from the EFFECT bus is output from this jack. This jack can be used to send the signal to an external effector, etc. y RETURN L (MONO), R Jacks These are unbalanced phone type line input jacks with a nominal input level/impedance of +4dB/ 600. The signal received by this jack is sent to GROUP buses 1-4, the STEREO bus and AUX1, AUX 2 buses. [. . . ] that drives the side speakers to the GROUP OUT (1-4) Jacks. w Use the GAIN Control on each channel to adjust the level of the input signal from the device or microphone that is connected to the input channel (refer to page 3), and use the Channel Fader to adjust the level of the output signal that is sent to the Master Section. Basically, you should set the Channel Fader close to the "0" position. e Press the "ST", "1-2", "3-4" GROUP, ST Select Switches on each channel. [. . . ]