User manual YAMAHA MW12CX

[. . . ] Owner's Manual Bedienungsanleitung Mode d'emploi Manual de instrucciones EN DE FR ES Español Français Deutsch English IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals in your plug proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. * This applies only to products distributed by Yamaha-Kemble Music (U. K. ) Ltd. [. . . ] Note that the signal level sent to the bus is also affected by the Channel fader I. On stereo channels (5/6, 7/8, 9/10, or 11/12), the signals from the L (odd) and R (even) channels are mixed and then sent to the EFFECT (AUX2) bus. 8 COMP Control Adjusts the amount of compression applied to the channel. As the knob is turned to the right the compression ratio increases while the output gain is automatically adjusted accordingly. The result is smoother, more even dynamics because louder signals are attenuated while the overall level is boosted. NOTE D PAN Control (1 to 4) PAN/BAL Control (5/6 and 7/8) BAL Control (9/10 and 11/12) The PAN control determines the stereo positioning of the channel signal on the REC L and R buses or on the Stereo L and R buses. The BAL control knob sets the balance between left and right channels. Signals input to the L input (odd channel) go to the REC L bus or to the Stereo L bus; signals input to the R input (even channel) go to the REC R bus or the Stereo R bus. NOTE Avoid setting the compression too high, as the higher average output level that results may lead to feedback. 9 PEAK Indicator The peak level of the post-EQ signal is detected, and the PEAK indicator lights red when the level reaches 3 dB below clipping. For XLR-equipped stereo input channels (5/ 6 and 7/8), both the post-EQ and post-mic-amp peak levels are detected, and the indicator lights red if either of these levels reaches 3 dB below clipping. 0 Equalizer (HIGH, MID, and LOW) This three-band equalizer adjusts the channel's high, mid, and low frequency bands. Channels 9/10 and 11/12 have two bands: high and low. Setting the knob to the position produces a flat response in the corresponding band. Turning the knob to the right boosts the corresponding frequency band, while turning to the left attenuates the band. The following table shows the EQ type, frequency, and maximum cut/boost for each of the three bands. Band HIGH MID LOW Type Shelving Peaking Shelving Frequency 10 kHz 2. 5 kHz 100 Hz ±15 dB Maximum Cut/Boost On channels where this knob provides both PAN and BAL control (channels 5/6 and 7/8), the knob operates as a PAN control when input is received via the MIC jack or L (MONO) input only, and as a BAL control when input is received via both L and R inputs. E ON Switch Turn this switch on to send the signal to the buses. The switch lights orange when on. F PFL (Pre-Fader Listen) Switch This switch lets you monitor the channel's pre-fader signal. Press the switch in ( ) so that it lights to turn it on. When the switch is on the channel pre-fader I signal is output to the PHONES and MONITOR OUT jacks for monitoring. G REC Switch This switch assigns the channel's signal to the REC L and R buses. NOTE To send the signal to the REC bus engage the ON switch ( ). A AUX (AUX1) Control Adjusts the level of the signal sent from the channel to the AUX (AUX1) bus. The knob should generally be set close to the position. On stereo channels, the signals from the L (odd) and R (even) channels are mixed and sent to the AUX (AUX1) bus. NOTE H ST Switch This switch assigns the channel's signal to the Stereo L and R buses. NOTE To send the signal to the Stereo bus engage the ON switch ( ). I Channel Fader Adjusts the level of the channel signal. Use these faders to adjust the balance between the various channels. NOTE To send the signal to the buses set the ON switch to on ( ). Set the fader sliders for unused channels all the way down to minimize noise. MW12CX/MW12C Owner's Manual 17 Reference Front & Rear Panels Master Control Section 1 2TR IN Jacks 2 1 These RCA pin jacks can be used to input a stereo sound source. Use these jacks when you want to connect a CD player directly to the mixer. NOTE 6 · Select where you want to send the signal using the 2TR IN/USB switch E, and adjust the signal level using the 2TR IN/USB control in the Master Control section. · A signals input via both the 2TR IN input and the USB input are mixed. 4 7 2 REC OUT 1 (L, R) Jacks These are RCA pin jacks that can be used to connect to an external stereo recorder. The signal processed by the REC OUT fader is output via these jacks. 5 3 8 3 REC OUT 2 (L, R) Jacks These are impedance-balanced TRS phone jacks that can be used to connect to an external stereo recorder. The signal processed by the REC OUT fader is output via the these jacks. B 9 4 RETURN L (MONO), R Jacks These are unbalanced phone-jack type line inputs. The signal received by these jacks is sent to the STEREO L/R bus and the AUX (AUX1) bus. [. . . ] 5F Ambience Corporate Tower Ambience Mall Complex Ambience Island, NH-8, Gurgaon-122001, Haryana, India Tel: 0124-466-5551 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S. A. 09300, México, D. F. , México Tel: 55-5804-0600 SPAIN/PORTUGAL Yamaha Música Ibérica, S. A. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 INDONESIA PT. Yamaha Musik Indonesia (Distributor) PT. [. . . ]