User manual YAMAHA MY16-EX

[. . . ] If this product is found to be the source of interference, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. [. . . ] If you cannot retrieve dropped objects yourself, refer the problem to qualified Yamaha service personnel. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. · The illustrations as shown in this Owner's Manual are for instructional purposes only, and may be different from the ones on your equipment. · The company names and product names in this Owner's Manual are the trademarks or registered trademarks of their respective companies. MY16-EX Owner's Manual 3 Introduction Introduction Thank you for purchasing the Yamaha MY16-EX I/O expansion card. The MY16-EX is a 16-channel digital input/output card that enables you to extend the number of channels of compatible cards, such as Yamaha MY16-ES64. Up to three MY16-EX cards can be daisy-chained. ENGLISH About the host devices in which the MY16-EX can be installed Before installing the card in a host device, please refer to the Yamaha Pro Audio web site for the latest information on the compatible host devices in which the card can be installed. Yamaha Pro Audio web site: http://www. yamahaproaudio. com · Ethernet is a trademark of Xerox Corporation. Installation information Please refer to the owner's manual supplied with the host device for installation information. As well as securing the card in place, the fixing screws at the left and right of the card function as electrical grounds. Be sure to screw them in tightly. Accessories Owner's Manual Ferrite core x 2 Part Names and Functions Panel 1 2 A [NEXT MY16-EX IN][NEXT MY16-EX OUT] Connectors These RJ-45 connectors can be connected via an Ethernet cable (CAT5e or higher category) to other MY16-EX cards for transmission and reception of the audio and word clock signals. Daisy-chain the cards in the following order: [NEXT MY16-EX OUT] connector [MASTER SIDE IN] connector on the next card in the daisy chain; [NEXT MY16-EX IN] connector [MASTER SIDE OUT] connector on the next card in the daisy chain. About the cable · Use an Ethernet CAT5e or higher category straight cable in which all eight (8) pins are connected. · Use an STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. Be sure to attach the included ferrite cores to a location close to the plug of each cable that is connected to the [NEXT MY16EX OUT] / [MASTER SIDE OUT] connectors. · Cables up to 3 meters in length can be used. B [MASTER SIDE IN][MASTER SIDE OUT] Connectors These RJ-45 connectors can be connected via an Ethernet cable (CAT5e or higher category) to the [NEXT MY16-EX IN] or [NEXT MY16-EX OUT] connector of the master card, such as a Yamaha MY16-ES64 or other MY16-EX cards, for transmission and reception of the audio and word clock signals. 4 MY16-EX Owner's Manual Part Names and Functions Switches ENGLISH SW1 3 2 1 SW2 48K 96K Emu. SW3 Nat. 4 SW105 OFF SW104 Set these switches as appropriate for your situation and for the device in which the card is installed. A Daisy-chain connection ID (SW1) Mode No. 1 No. 2 No. 3 Position 1 2 3 Assign an ID number to each card in the daisy-chain in sequence, starting with the card closest to the master card (such as the MY16-ES64). B Sampling Frequency (SW2) Mode 44. 1/48 kHz 88. 2/96 kHz Position 48K 96K NOTE: This card supports only Double Speed mode when running at 88. 2/96kHz. (Double Channel mode is not supported. ) C Card ID (SW3) Mode Emulation Native Position Emu. Nat. Typically set this switch to the [Emu. ] position. If you set this switch to the [Emu. ] position and switch 2 (SW2) to the [48K] position, the host device will recognize the card as a Yamaha MY16-AT digital I/O card. If you set this switch to the [Emu. ] position and switch 2 (SW2) to the [96K] position, the host device will recognize the card as a Yamaha MY8-AE96 digital I/O card. If you install the card in a host device whose firmware supports the MY16-EX, setting this switch to the [Nat. ] position enables you to make best use of the MY16-EX function. OFF 1 2 3 D SW104/SW105 Leave these switches permanently set to the [OFF] position during use. [. . . ] #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 ARGENTINA Yamaha Music Latin America, S. A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 SWEDEN Yamaha Scandinavia AB J. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 TAIWAN Yamaha KHS Music Co. , Ltd. [. . . ]