User manual YAMAHA MY16-MLAN

[. . . ] If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. (class B) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Address : Telephone : Type of Equipment : Model Name : Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. 90620 714-522-9011 EtherSound INTERFACE CARD MY16-MLAN This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. [. . . ] · Do not touch the metallic leads (pins) of the circuit board when handling the card. The pins are sharp and may cause hand cuts. · Wear a pair of heavy gloves during installation to avoid scratching or cutting your hands on sharp edges. · Avoid touching exposed connectors and metal parts to minimize the possibility of bad connections. · Drain all static electricity from your clothing and body before handling the card. Touch an exposed metal part of the host device or other grounded object beforehand. · Do not drop the card or subject it to physical shock as this can result in breakage and/or malfunction. · Do not drop screws or other small parts inside the card. If power is applied while screws or similar metal objects are loose inside the unit the card may malfunction or be damaged. If you cannot retrieve dropped objects yourself, refer the problem to qualified Yamaha service personnel. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. · The illustrations as shown in this Owner's Manual are for instructional purposes only, and may be different from the ones on your equipment. You will set this switch to the [BOOT] position to update the firmware in the future. Typically set this switch to the [422] position. When you connect the [HA REMOTE] connector to a computer, set this switch to the [232] position. B Sampling Frequency (SW2) Mode 44. 1/48 kHz 88. 2/96 kHz Position 48K 96K E SW201 Leave this switch permanently set to the [OFF] position during use. Otherwise the card will not operate properly. NOTE: This card supports only Double Speed mode when running at 88. 2/96kHz. (Double Channel mode is not supported. ) Word Clock Master Settings on the host devices The word clock master settings will differ as per the following chart, depending on whether the MY16-MLAN card(s) (that are not a primary master) have been installed in the same device as the primary master MY16-MLAN card. Primary Master Other than Primary Master Select "SLOT" C Card ID (SW3) Mode Emulation Native Position Emu. If installed in different devices If installed in the same device Select other than "SLOT" Typically set this switch to the [Emu. ] position. If you set this switch to the [Emu. ] position and switch 2 (SW2) to the [48K] position, the host device will recognize the card as a Yamaha MY16-AT digital I/O card. If you set this switch to the [Emu. ] position and switch 2 (SW2) to the [96K] position, the host device will recognize the card as a Select other than "SLOT" * SLOT: Indicates the slot in which the MY16-MLAN is installed. MY16-MLAN Owner's Manual 5 ENGLISH NOTE: OnChip BOOT 96K Connection Example Î Connection Example ENGLISH EtherSound Device (Yamaha DME Satellite series, NAI48-ES etc. ) DEUTSCH FRANÇAIS ESPAÑOL ITALIANO Computer or EtherSound Device Ethernet Cable MY16-MLAN (1­16 ch) Ethernet Straight Cable MY16-EX #1 (17­32 ch) Ethernet Straight Cable MY16-EX #2 (33­48 ch) Ethernet Straight Cable MY16-EX #3 (49­64 ch) 26 MY16-MLAN Owner's Manual Appendix Appendix Connector Pin Assignment HA REMOTE Pin No. 6 7 8 9 Signal Name RX+ RTS CTS N. C 164. 1 120 European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Conforms to Environments: E1, E2, E3 and E4 Unit: mm 40 * Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. [. . . ] Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-013 Sao Paulo, SP. BRAZIL Tel: 011-3704-1377 SPAIN/PORTUGAL Yamaha-Hazen Música, S. A. [. . . ]