User manual YAMAHA NS-10MM

[. . . ] Natural Sound 2-way Acoustic-suspension Speaker System Thank you for selecting this Yamaha NS-10MM speaker system. NS-10MM s TO MOUNT THE SPEAKERS ON A WALL Attach the provided mounting bracket to the rear of the speaker by using the provided screws. PRECAUTIONS Read these precautions carefully before using your speaker. Any time you note distortion, reduce the volume control on your amplifier to a lower setting. Never allow your amplifier to be driven into "clipping". [. . . ] YAMAHA shall not be liable for any accident caused by improper placement or installation of the speaker. Remove the provided pads from the paper, and put the pads at both ends on the lower side of the speaker. PLACING THE SPEAKERS s TO STAND THE SPEAKERS Place the speakers on a sturdy, vibration-free surface. If you cannot obtain good bass quality when the speakers are placed directly on the floor, insert a block etc. Better stereo images will be obtained when the speakers are slightly angled in towards the listeners. Fasten screws into a firm wall or wall support as shown in the diagram, and hang the holes of the mounting bracket on the protruding screws. Diam. 12 mm 2 mm Tapping screw (Available at a hardware store) Wall or wall support 40 mm Make sure that the screws are caught by a narrow part of the holes securely. Note Because this speaker is not a magnetic shielding type, there may be some influence on a TV picture depending on the type of TV or the placement of the speaker. In such a case, place the speaker apart from the TV so that there is no influence on TV picture. WARNING: * Each speaker weighs 1. 5 kg (3 lbs. Do not mount them on thin plywood or soft wall surface material, as the screws may come out of the flimsy surface, causing the speakers to fall down and be damaged, or result in personal injury. * Do not fasten the speakers to wall with nails, adhesives, or other unsound hardware. Long-term use and vibrations may cause them to fall down. * To avoid accidents resulting from tripping over loose speaker cables, fix them to the wall. CONNECTION TO YOUR AMPLIFIER BEFORE MAKING CONNECTIONS, MAKE SURE THAT THE AMPLIFIER IS SWITCHED OFF. s CONNECTIONS Connect the push-type input terminals at the rear of the speakers to the speaker output terminals of your amplifier with the provided speaker cables. One side of the speaker cable is marked by a blue line. Connect the (+) terminals on both the amplifier and the speakers using this blue-marked side. Connect the (­) terminals on both components using the unmarked side of the cable. Connect one speaker to the left (marked L) terminals of your amplifier, and another speaker to the right (marked R) terminals, making sure not to reverse the polarity (+, ­). [. . . ] (Depth of hole : 8mm) 60 mm Speaker (R) Speaker (L) SPECIFICATIONS Type . . . . . . . . . . . . . . . . . . . . . . . . . 2-way acoustic-suspension speaker system Speaker Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 cm cone woofer 2. 5 cm tweeter Input Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Push-type Nominal Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ohms Frequency Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Hz ­ 20 kHz Nominal Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40W Maximum Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100W Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 dB/w/m Crossover Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 kHz Dimensions (WxHxD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 x 191 x 140 mm (4-3/8" x 7-1/2" x 5-1/2") Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 5 kg (3 lbs. 5 oz. ) Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Speaker cable (10m) x 2 Mounting bracket x 2 Screw x 4 Pad x 4 Blue line Blue line Speaker output terminals of the amplifier Note Do not let the bare speaker wires touch each other as this could damage the speaker and/or the amplifier. * Specifications subject to change without notice due to product improvements. * Care should be taken not to exceed the input power values noted above. VU 94700 [. . . ]