User manual YAMAHA NX-SW70

[. . . ] As these speakers contain strong magnets (though all of them are magnetically shielded types), avoid placing watches, magnetic tapes, etc. Also, placing the speakers near a TV set may impair picture color. If this happens, move the speakers away from the TV set. Do not attempt to clean the speakers with chemical solvents as this might damage the finish. [. . . ] Check that the wood screws are secure inside the narrow portion of the holes in the bracket. s To mount speakers directly to the wall It is possible to hang the speakers directly on the wall without using the type A brackets by attaching two wood screws to the wall and then using the holes on the rear panel of the speakers for direct attachment. Wood screws having a diameter of about 4 to 5 mm (commercially available) 65 mm 65 mm 65 mm 20 mm or more Type A bracket 2 Attach the speaker to the bracket using the provided wing nut. 5 mm 20 mm or more Note · After mounting, check that the speakers are attached securely. s YAMAHA speaker stand SPS-AV1 (sold separately) The rear speakers can also be attached to SPS-AV1 speaker stands and used as floor stand speakers. Wing nut (provided) 3 Adjust the angle of the speaker and then tighten the wing nut. English 3 USING THE SPEAKER MOUNTING BRACKETS Using Commercially Available Speaker Stands (distance between screw holes: 60 mm) 1 Attach the type B brackets to the bottom of the speakers using the provided screws. Align so that the protrusion on the bracket goes into the groove on the bottom of the speaker. CAUTION Be sure to read these important precautions. · Each speaker weighs approximately 0. 7 kg. Select a firm wall or pillar to attach screws to. Do not attach screws to material such as mortar or veneer as screws may come loose easily, causing the speaker to fall. · Do not mount speakers using nails or tape as vibrations during operation may cause nails to come loose or tape to peel off, causing the speaker to fall. · Take care that the speaker cord is not pinched between the speaker and the bracket. Be sure that the speaker cord passes through the groove on the rear panel of the speaker. · Secure the speaker cords so that they will not catch on hands or feet, causing speakers to drop. · Be absolutely sure to check for safety after speakers are mounted. YAMAHA bears no responsibility for damage caused due to improper installation or installation in an improper location. Provided screw Type B bracket 2 Mount the speaker on the speaker stand using the bracket holes (spaced at 60 mm). Be sure to ready the small screws (diameter: 4 mm, length: 8 mm), spring washers and washers. 60 mm 4 CONNECTIONS CAUTION Always be sure to turn off the power of any component to be connected when making connections. To ensure proper connections · After connections have been made, check one more time that wiring has been made properly. Connecting the Rear Speakers to the Subwoofer Note · Do not connect any speakers to the speaker terminals on the subwoofer except for provided rear speakers (NX-AVS70). Damage may result if a different speaker is connected. y Remove the plastic insulation from the ends of the speaker cords and twist the bare wires. (The bare wire will stay neat if you twist while removing the plastic insulation. ) REAR SPEAKERS R MARK L SYSTEM CONNECTOR DO NOT CONNECT THIS UNIT TO SPEAKERS OTHER THAN NX-AVS70 REAR R Speaker cord identification labels ­ + REAR L ­ + Right rear speaker Left rear speaker English 5 CONNECTIONS s Connect the speaker cords to the speaker terminals on the subwoofer. 31 2 Bare wire 1 Tab Hold up the tab for the + terminal (red), or hold down the tab for the ­ terminal (black). Insert the bare wire of the speaker cord into the hole. 2 3 Release the tab. · Connect the line-in cord to the + terminal (red), and the other cord to the ­ terminal (black). · Once connected, pull gently on the speaker cords to check that they are connected securely. CAUTION · Do not let the bare speaker wire touch each other and do not let them touch any metal part of the speakers. · Do not mistakenly connect plus (+) to minus (­) or vice versa when connecting speaker cords. · Insert the speaker cords securely so that plus (+) and minus (­) do not short. The speaker may not output any sound or may output noise, causing damage to the speakers, if speaker cords are not inserted securely. · Only insert the bare wire portion of the speaker cords into the holes. [. . . ] Type B brackets (x 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screws (x 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wing nuts (x 2) Specifications are subject to change without notice. English 9 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE. , BUENA PARK, CALIF. 135 MILNER AVE. , SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G. m. b. H. [. . . ]