User manual YAMAHA P-200

[. . . ] SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded / stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. [. . . ] The significance in this case is that turning the [MIDI] button off affects all of the Performances, whereas the aforementioned Edit mode settings can be assigned to individual Performances. For details about the P-200's MIDI capabilities, see page 64. 40 s MIDI Panic Although MIDI is very reliable, it is in fact so sophisticated that it is not without its occasional faults. For example, sometimes a connected tone generator or synthesizer responds to a Note On message, but not a Note Off message, thus causing a note to get stuck, which can be quite frustrating, especially in a live performance setting. Unexpected sustained notes, sudden losses of volume, and "hanging" pitch bends are also common MIDI problems that can happen when using a sequencer with the P-200 and other MIDI instruments. The P-200's MIDI Panic feature lets you instantly send note off and other messages to all connected MIDI devices. ACTIVATING MIDI PANIC Hold the [MIDI] button, then press the [REVERB] and [MODULATION] buttons at the same time. EFFECT REVERB MODULATION CHORUS SYMPHONIC TREMOLO MIDI + ROOM STAGE HALL PAGE The MIDI PANIC SEND screen appears briefly when MIDI Panic is activated. ç MIDI PANIC é è SEND ê When MIDI Panic is activated, the following messages are sent in sequence over all MIDI channels: All Notes Off; All Sounds Off; Channel Pressure off; Sustain Pedal Off; Modulation Off; Pitch Bend (Center); Reset All Controllers. MIDI Panic has no effect during sending/receiving bulk data or while MIDI Merge is on. s Panel Switch Lock This function allows you to "lock" the panel controls of the P-200, in order to avoid accidentally changing voices or modes in the middle of a performance. In order to use this function, the separate Panel Switch Lock Mode function must be set to "enable. " (See page 52. ) The default setting for Panel Switch Lock is "off. " 41 USING THE PANEL SWITCH LOCK FUNCTION From the Voice Play mode or the Performance Play mode, double-click the desired [VOICE SELECT] button. (Refer to "About Panel Switch Lock" below for details. ) The following screen appears when Panel Switch Lock is activated. PANEL LOCK Piano 1 Voice/Performance name To cancel the lock function, double-click the same [VOICE SELECT] button (the button whose LED is lit). q About Panel Switch Lock The use of the Panel Switch Lock function differs depending on the mode (Single, Dual, Split). The illustrations below clearly show how to lock and unlock the panel controls in various situations. The following key is used in the illustrations: Normal button press "Double-click" button press Locked condition Unlocked condition In the Single mode: Normal operation Voice A Voice A Voice A Voice A Voice B Voice B q Double-clicking the same [VOICE SELECT] button (the button whose LED is lit) alternately locks and unlocks the panel controls. Double-clicking a different [VOICE SELECT] button when the panel is locked maintains the locked condition while selecting a new voice. 42 In the Dual mode: Voice C Voice A Normal operation + Voice B Voice A + Voice B (Dual mode) Voice A or Hold down Voice A and double-click Voice B. Voice C Voice A or Voice B Voice B q Selecting the Dual mode and locking the panel are done in a single operation: Hold down one [VOICE SELECT] button and double-click another. q When the panel is locked, you can unlock it by double-clicking the [VOICE SELECT] button whose LED is lit. This also exits the Dual mode and returns to the Single mode. q Double-clicking a [VOICE SELECT] button whose LED is NOT lit (as with Voice C above) maintains the locked condition, but exits the Dual mode and selects a new voice in the Single mode. In the Split mode: The first illustration shows how to lock the panel. The second illustration shows how to unlock it. In both illustrations, the top voice is the sub voice and the bottom is the main voice: Sub voice/Main voice SPLIT + Voice A Hold down SPLIT and double-click Voice A. Voice B Voice A/Voice B Normal operation (Voice B) SPLIT + Voice A Hold down SPLIT and press Voice A. Voice A/Voice B (Split mode) Voice C Voice A/Voice C SPLIT + Voice D Hold down SPLIT and double-click Voice D. Voice D/Voice B q There are two ways to select the Split mode and lock the panel: A) Direct operation ­ 1) Select the main voice. 2) Hold down [SPLIT] and double-click the desired [VOICE SELECT] button. B) Selecting Split mode and locking panel separately ­ 1) Select the main voice. 2) Hold down [SPLIT] and select the sub voice to enter the Split mode. 3) Double-click the desired [VOICE SELECT] button to lock the panel. This simultaneously puts the panel in the locked condition and selects a new main voice. [. . . ] Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. 16-28, Jalan SS 2/72, Petaling Jaya, Selangor, Malaysia Tel: 3-717-8977 BRASIL Yamaha Musical do Brasil LTDA. Reboucas 2636, São Paulo, Brasil Tel: 011-853-1377 PHILIPPINES Yupangco Music Corporation 339 Gil J. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 ARGENTINA Yamaha Music Argentina S. A. [. . . ]