User manual YAMAHA P-850

[. . . ] (5) Omni Off (reception only) ccH Parameter Data Range (vvH) 7CH Omni Off 00H Same processing as for All Notes Off. (6) Omni On (reception only) ccH Parameter Data Range (vvH) 7DH Omni On 00H Same processing as for All Notes Off. (7) Mono (reception only) ccH Parameter Data Range (vvH) 7EH Mono 00H Same processing as for All Sound Off. (8) Poly (reception only) ccH Parameter Data Range (vvH) 7FH Poly 00H Same processing as for All Sound Off. [. . . ] · When Control Change is turned OFF, Control Change messages will not be transmitted or received. · Local on/off, OMNI on/off are not transmitted. (The appropriate note off number is supplied with "All Note Off" transmission). · When a voice bank MSB/LSB is received, the number is stored in the internal buffer regardless of the received order, then the stored value is used to select the appropriate voice when a program change message is received. This mode will not change when the instrument receives a MONO/POLY mode message. Data Range (vvH) 00H. . . 7FH (3) Expression (reception only) ccH Parameter Data Range (vvH) 0BH Expression MSB 00H. . . 7FH (4) Sustain ccH Parameter 40H Sustain MSB (5) Sostenuto ccH Parameter 42H Sostenuto (6) Soft Pedal ccH Parameter 43H Soft Pedal Data Range (vvH) 00H. . . 7FH Data Range (vvH) 00H. . . 3FH:off, 40H. . . 7FH:on Data Range (vvH) 00H. . . 3FH:off, 40H. . . 7FH:on (7) Effect1 Depth (Reverb Send Level) ccH Parameter Data Range (vvH) 5BH Effect1 Depth 00H. . . 7FH Adjusts the reverb send level. (8) Effect4 Depth (Variation Effect Send Level) ccH Parameter Data Range (vvH) 5EH Effect4 Depth 00H. . . 7FH (9) RPN 65H RPN MSB 64H RPN LSB 06H Data Entry MSB 26H Data Entry LSB 60H Data Increment 61H Data Decrement * Parameters that are controllable with RPN: Coarse Tune, Fine Tune, Pitch Bend Range [2] P-85 Data List 4. PROGRAM CHANGE Data format: [CnH] -> [ppH] CnH = Program event (n = channel number) ppH = Program change number P. C. #=Program Change number Voice Name MSB LSB P. C. # 0 122 1 Grand Piano 1 0 112 1 Grand Piano 2 0 122 6 E. Organ 2 0 122 49 Strings 0 122 7 Harpsichord 1 0 123 7 Harpsichord 2 122 12 0 Vibraphone · When program change reception is turned OFF, no program change data is transmitted or received. · When you specify a program change as a number in the range of 0­127, specify a number that is one less than the program change number listed above. (2) XG Native Bulk Data (reception only) Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] -> [bbH] -> [hhH] -> [mmH] -> [llH] -> [ddH] ->. . . -> [ccH] -> [F7H] F0H = Exclusive status 43H = YAMAHA ID 0nH = When received, n=0­F. 4CH = Model ID of XG aaH = ByteCount bbH = ByteCount hhH = Address High mmH = Address Mid llH = Address Low ddH = Data | | | | ccH = Check sum F7H = End of Exclusive · Receipt of the XG SYSTEM ON message causes reinitialization of relevant parameters and Control Change values. Allow sufficient time for processing to execute (about 50 msec) before sending the P-85 another message. · XG Native Parameter Change message may contain two or four bytes of parameter data (depending on the parameter size). · For information about the Address and Byte Count values, refer to Table 1 below. Note that the table's Total Size value gives the size of a bulk block. Only the top address of the block (00H, 00H, 00H) is valid as a bulk data address. SYSTEM EXCLUSIVE MESSAGES (Digital Piano MIDI Format) Data format: [F0H] -> [43H] -> [73H] -> [01H] -> [xxH] -> [F7H] F0H = Exclusive status 43H = Yamaha ID 73H = Digital Piano ID 01H = Product ID (digital piano common) xxH = Substatus nn Control 02H Internal MIDI clock 03H External MIDI clock 06H Bulk Data (the bulk data follows 06H) F7H = End of Exclusive 10. SYSTEM EXCLUSIVE MESSAGES (Special Control) Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] -> [0nH] -> [ccH] -> [vvH] -> [F7H] F0H = Exclusive status 43H = Yamaha ID 73H = Digital Piano ID 7FH = Extended Product ID 4BH = Product ID 11H = Special control 0nH = Control MIDI change (n=channel number) ccH = Control number vvH = Value F7H = End of Exclusive Control Channel Detune Channel ccH vvH ch: 00H­0FH 43H (Sets the Detune value for each channel) 00H­7FH Voice Reserve ch: 00H­0FH 45H 00H : Reserve off 7FH: on* * When Volume, Expression is received for Reserve On, they will be effective from the next Key On. [. . . ] SYSTEM EXCLUSIVE MESSAGES (Special Control) Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] -> [0nH] -> [ccH] -> [vvH] -> [F7H] F0H = Exclusive status 43H = Yamaha ID 73H = Digital Piano ID 7FH = Extended Product ID 4BH = Product ID 11H = Special control 0nH = Control MIDI change (n=channel number) ccH = Control number vvH = Value F7H = End of Exclusive Control Channel Detune Channel ccH vvH ch: 00H­0FH 43H (Sets the Detune value for each channel) 00H­7FH Voice Reserve ch: 00H­0FH 45H 00H : Reserve off 7FH: on* * When Volume, Expression is received for Reserve On, they will be effective from the next Key On. SYSTEM EXCLUSIVE MESSAGES (Others) Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H] -> [00H] -> [mmH] -> [llH] -> [ccH] -> [F7H] Master Tuning (XG and last message priority) simultaneously changes the pitch of all channels. F0H = Exclusive Status 43H = Yamaha ID 1nH = When received, n=0­F. 27H = Model ID of TG100 30H = Sub ID 00H = 00H = mmH = Master Tune MSB llH = Master Tune LSB ccH = irrelevant (under 7FH) F7H = End of Exclusive [4] P-85 Data List <Table 1> MIDI Parameter Change table (SYSTEM) Address (H) Size (H) Data (H) 00 00 00 4 020C­05F4(*1) 01 02 03 Parameter MASTER TUNE 04 1 00­7F 7E 00 7F 00 TOTAL SIZE 07 *1: Values lower than 020CH select -50 cents. [. . . ]