User manual YAMAHA P1150 P1250 P2150 P2250

[. . . ] Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i. e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: ­ Other components, as they may cause damage and/or discoloration on the surface of this unit. [. . . ] ­ when 2-channel signals are being input. 46 En Enjoying surround sound Enjoying 2-channel sources in surround sound This unit can decode 2-channel sources for 5. 1-channel playback so that you can enjoy a variety of surround sound effects by switching the surround mode. y The beam mode must be set to 5 Beam, Stereo plus 3 Beam, or 3 Beam (see page 44). 5BEAM ST+3BEAM 3BEAM 2 Press SUR. DECODE and then press / ) to switch between surround modes. Choices: Neo:6 Cinema, Neo:6 Music, PRO LOGIC, PLII Movie, PLII Music, PLII Game Default setting: Neo:6 Cinema SUR. DECODE 1 STEREO 2 MY BEAM 3 MY SUR. or 4 7 0 CH LEVEL 5 8 +10 6 9 SUR. DECODE ENTER MENU ENTER TEST TV/AV YSP RETURN Neo:6 Cinema 1 Set the operation mode selector to YSP. TV/AV YSP Neo:6 Music PRO LOGIC PLI Movie I PLI Music I PLI Game I BASIC OPERATION English 47 En Enjoying surround sound Enjoying TV in surround sound You can enjoy analog audio signals output from your TV in real surround sound. y Before performing the steps below, set the volume of this unit to 30. If necessary, adjust the volume level in step 4 below. 4 If you hear sound from your TV speakers, reduce the volume level of your TV until you can no longer hear any audio being output. To reduce the TV volume level, use the remote control supplied with your TV. Press VOLUME +/­ to adjust the volume level. VOLUME 5 INPUT1 TV INPUT2 MACRO TV AUTO VOL MODE SETUP INPUTMODE SLEEP 5BEAM ST+3BEAM 3BEAM 1 STEREO 2 MY BEAM 3 MY SUR. 4 7 0 CH LEVEL 5 8 +10 6 9 SUR. DECODE MENU 6 ENTER TEST TV/AV YSP RETURN VOLUME CH TV VOL Press SUR. "STEREO" appears in the front panel display. STEREO 4 XSTEREOXMODE 50 En PLAYING BACK SOUND CLEARLY (MY BEAM) Playing back sound clearly (My Beam) You can improve listenability in a noisy environment by changing the beam mode to My Beam, which outputs sound beams directly toward the listening position in a single channel. In addition, My Beam is also ideal when you do not want the sound beams to be reflected on the walls in your listening room or when you do not want to disturb other people while enjoying music or movies at night. My Beam microphone STANDBY/ON POWER POWER AV TV SLEEP 5BEAM ST+3BEAM 3BEAM 1 STEREO 2 MY BEAM 3 MY SUR. 4 7 0 CH LEVEL 5 8 +10 6 9 SUR. DECODE MENU ENTER TEST TV/AV YSP RETURN Note BASIC OPERATION If My Beam is selected as the beam mode, the surround modes (see page 46) and TruBass (see page 63) become ineffective. In addition, no audio is output from the subwoofer connected to this unit. Using auto-adjust function The My Beam microphone on the remote control collects the test tones from this unit so that the beam angle can be automatically adjusted. Notes · If an error occurs, an error buzzer is played and "MY BEAM ERROR" is displayed in the front panel display. · An error may occur if the listening room is noisy. Make sure that the listening room is as quiet as possible while the test tones are being output. · Do not shake or move the remote control while the test tones are being output. · Do not cover the My Beam microphone on the remote control while the test tones are being output. · The batteries in the remote control may be weak if the remote control does not function properly. In this case, replace all the batteries and then try the procedure again. · When the input signal with 64 kHz, 88. 2kHz, or 96 kHz of sampling frequency is being played back, the beam angle cannot be automatically adjusted. 1 Set the operation mode selector to YSP. TV/AV YSP 2 Press and hold MY BEAM for more than two seconds. [. . . ] If the menu screen does not appear, check the OSD video pin cable (see the connection example on the front page). TV INPUT2 The setup screen automatically changes during the AUTO SETUP procedure. When the AUTO SETUP procedure is completed, the following screen appears on the TV. 2 Set the operation mode selector to YSP. This unit switches to the YSP operation mode. INTELLIBEAM MIC SHOW RESULT MEASUREMENT COMPLETE BEAM MODE :5 BEAM SUBWOOFER :NOT APPLICABLE IntelliBeam microphone (supplied) INPUT1 MACRO Cardboard microphone stand (supplied) TV AUTO VOL MODE SETUP INPUTMODE SLEEP AUTO SETUP PREPARATION & CHECK Please connect the MIC. Please place the MIC at least 1. 8m/6ft away from the YSP unit. The MIC should be set at ear level when seated. [. . . ]