User manual YAMAHA P2040

[. . . ] We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: BATTERY NOTICE : This product MAY contain a small nonrechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. [. . . ] For example, if you want the transpose amount to be one octave below normal keyboard pitch, simply press C2. To return the transpose amount to normal pitch, simply press C3 again. You can also change the transpose amount setting one semitone at a time by holding the [TRANSPOSE] button and pressing the [­1/NO] and [+1/YES] buttons. You can set the transpose amount anywhere within a range of four octaves, from -24 (C1) to 24 (C5). If you try to set the transpose amount by pressing a key below C1 or above C5 on the keyboard, the P-200 will react as though you pressed C1 or C5. NOTE In this case you cannot use the [CS] slider to change the transpose value. (Trying to do so in Dual mode will activate the detune function. ) NOTE When the transpose setting exceeds the legal range (A­1 ~ C7) the P-200 plays and repeats the one octave higher (or lower) range. Also note that MIDI notes will not be transmitted if the data exceeds MIDI note values 0 ~ 127. 2. Release the [TRANSPOSE] button. The P-200 will assume that you want to transpose using this value, and leave the transpose function turned on after you complete the setting. In a similar way, internal sub voice and MIDI transpose signals for the MIDI main and sub voice can be set independently, as explained below. INTERNAL SPLIT SUB VOICE: To set the transpose value for the internal split sub voice, in Split mode, press and hold [TRANSPOSE], then hold [SPLIT], then press a key on the keyboard (or press the [­1/NO] or [+1/YES] buttons). ! TRANSPOSE DETUNE + + " SPLIT BALANCE # TRANSPOSE SPLIT SUB $ +12 INTERNAL DUAL SUB VOICE: To set the transpose value for the internal dual sub voice, in Dual mode, press and hold [TRANSPOSE], then hold [SPLIT], then press a key on the keyboard (or press the [­1/NO] or [+1/YES] buttons). TRANSPOSE DUAL SUB $ +12 39 MIDI MAIN VOICE: To set the transpose value for the MIDI main voice, press and hold [TRANSPOSE], then hold [MIDI], then press a key on the keyboard (or press the [ ­1/NO] or [+1/YES] buttons). ! TRANSPOSE DETUNE + + " MIDI PAGE # TRANSPOSE MIDI MAIN $ +12 NOTE When changing the internal main or sub voice's transpose value, the MIDI main or sub voice will change accordingly. MIDI SUB VOICE: To set the transpose value for the MIDI sub voice, press and hold [TRANSPOSE], followed by [SPLIT], then [MIDI], then press a key on the keyboard (or press the [­1/NO] or [+1/YES] buttons). ! TRANSPOSE DETUNE + " SPLIT BALANCE + $ # MIDI PAGE + TRANSPOSE MIDI SUB $ +12 s MIDI Transmit Enable You can enable or disable MIDI transmission by pressing the [MIDI] button. The LED above the [MIDI] button remains lit while this function is enabled. MIDI PAGE It will not block the reception of data from the [MIDI IN] jack. 3) Double-click the desired [VOICE SELECT] button to lock the panel. This simultaneously puts the panel in the locked condition and selects a new main voice. To select a different sub voice and lock the panel (while the Split mode is active), hold down [SPLIT] and double-click the desired [VOICE SELECT] button. 43 Voice B Voice A/Voice B Voice A/Voice B Voice A Voice A/Voice A Voice C Double-clicking a different voice maintains the panel lock and selects a new main voice. Voice A/Voice C q To unlock the panel, simply double-click the main or sub voice's [VOICE SELECT] button. q Double-clicking a different [VOICE SELECT] button when the panel is locked in the Split mode maintains the locked condition while selecting a new main voice. 44 PERFORMANCE PLAY MODE Within Performance Play mode you can select and play any one of the 24 Performances, make changes in a Performance, or store the settings of one Performance into another Performance bank and number. Following is an overview of how to enter and exit Performance Play mode, how to select the Performances and change voices within a Performance, and the way Single, Dual and Split modes function in Performance Play mode. ENTERING AND EXITING PERFORMANCE PLAY MODE 1. Press the [PERF. A] button, the LED above it will start blinking to indicate that the P-200 is standing by to enter the PERFORMANCE-A bank. B] button, the LED above it will start blinking to indicate that the P-200 is standing by to enter the PERFORMANCE-B bank. PERF. B 2. Press a [PERFORMANCE SELECT] button. Pressing a [PERFORMANCE SELECT] button activates Performance mode. The LEDs above the [PERFORMANCE SELECT] and [PERF. ] buttons light, and the name of the Performance appears in the LCD screen. PERF. B VOICE PIANO 1 2 PIANO 2 3 PIANO 3 4 PIANO 4 5 6 7 8 VIBES E. PIANO 1 E. PIANO 2 E. PIANO 3 SYSTEM MIDI FILTER PC TABLE CHANNEL LOCAL CS FC PS NAME PERFORMANCE<A01> Piano 1 To exit Performance Play mode, simply press the [VOICE] button, followed by a [VOICE SELECT] button, which will return you to Voice Play mode. 45 SELECTING A PERFORMANCE Press a [PERFORMANCE SELECT] button. [. . . ] 4, Jakarta 12930, Indonesia Tel: 21-520-2577 PORTUGAL Valentim de Carvalho CI SA Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras, Portugal Tel: 01-443-3398/4030/1823 CENTRAL & SOUTH AMERICA MEXICO Yamaha de Mexico S. A. De C. V. , Departamento de ventas Javier Rojo Gomez No. 1149, Col. Tel: 686-00-33 KOREA Cosmos Corporation #131-31, Neung-Dong, Sungdong-Ku, Seoul Korea Tel: 02-466-0021~5 GREECE Philippe Nakas S. A. Navarinou Street 13, P. Code 10680, Athens, Greece Tel: 01-364-7111 SWEDEN Yamaha Scandinavia AB J. [. . . ]