User manual YAMAHA P2700

[. . . ] · If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. · Always set the product on a flat and solid surface. [. . . ] Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. · When setting up the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. Doing so may result in injury or damage/deterioration to the product. · Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. · Watch your fingers when adjusting clamps. They may become pinched, resulting in injury. · Be careful around pipe ends, inside the pipe and screw ends. · Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. · Do not attach acoustic drums to the electronic drum rack. If necessary, use clamp bolts A to E to adjust the height and angle of the snare pad. When doing so, be sure to adjust one bolt at a time (i. e. , loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt B Clamp bolt 1. Attach the clamp bolt to the snare pad and provisionally tighten (by 5 or 6 turns). Clamp bolt (to be tightened in the direction shown) Snare pad (rear side) 3. If necessary, use clamp bolts A to D to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i. e. , loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt B 4 5 1. Position the kick pad as desired, referring to the standard assembly example on the other side. NOTICE Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard boxes on the floor under the kick pad to protect it from damage. Connect the pads to the drum trigger module. As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module. Clamp bolt D Clamp bolt E Clamp bolt A Clamp bolt C Clamp bolt A Clamp bolt C Clamp bolt D Insert the 9-channel snake cable's straight plugs into the drum trigger module's trigger input jacks ([q SNARE] to [i KICK/o] and [HI-HAT CONTROL]). · If you are using the standard setup, the stickers on each of the snake cable's plugs will indicate the name of the corresponding pad. 2. Plug the 9-channel snake cable's L-shaped plugs into the correct pads. [Locations of pad jacks] [Drum trigger module's rear panel] Mounting the drum trigger module, cymbal pads, and hi-hat pad Cymbal pad: PCY100 Hi-hat pad: PCY100 Drum trigger module Cymbal pad: PCY135 1 2 3 4 Mounting the cymbal pads 1. 5. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper's key bolt using a tuning key. [Cymbal pad] [Hi-hat pad] Using a tuning key, loosen the stopper's key bolt. 5 6 7 8 9 DTX500 jack names 1: qSNARE 2: wTOM1/!0 3: eTOM2/!1 4: rTOM3/!2 5: tRIDE 6: yCRASH 7: uHI-HAT 8: iKICK/o 9: HI-HAT CONTROL Stopper Key bolt Straight plug names (as shown on stickers) Bolt cover Tuning key Full contact Stopper Bolt cover [9-channel snake cable] Straight plugs 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. Wing nut Felt pads Cymbal holder Full contact SNARE TOM1 TOM2 TOM3 RIDE CRASH HI HAT KICK HH CON 3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being pulled out. L-shaped plugs HH CON HI HAT CRASH KICK SNARE TOM1 TOM2 TOM3 RIDE 6. Place one of the felt pads removed in Step 2 on the cymbal holder. NOTICE Mounting the drum trigger module Bolt cover 7. 1. Attach the module stand (provided) to the underside of the drum trigger module using the module stand fastening screws. Cymbal holder Mount the pad unit on the cymbal stand. [. . . ] Place one of the felt pads removed in Step 2 on the cymbal holder. NOTICE Mounting the drum trigger module Bolt cover 7. 1. Attach the module stand (provided) to the underside of the drum trigger module using the module stand fastening screws. Cymbal holder Mount the pad unit on the cymbal stand. Lower the pad unit into place with the cymbal holder's shaft passing through the central hole of the cup section. When mounted, the stopper's pin should rest inside the pad unit's smaller hole. * If you were to play a cymbal pad without the stopper's pin positioned inside the smaller hole, the pad could rotate, causing the cable to be pulled out. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. Excessive bending can damage the pad cables. [. . . ]