User manual YAMAHA PC3000A

[. . . ] Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable such as cutting the wires, etc. · Owner's Manual (this sheet) X1 The connector has two black rings. (The monaural type connector has one black ring. ) Output Level Adjustment Controls the level of the trigger output from the PC3000A/130S/150S. [. . . ] (The monaural type connector has one black ring. ) Output Level Adjustment Controls the level of the trigger output from the PC3000A/130S/150S. Rotate the knob to the right (+) to increase the output level, or to the left (­) to decrease output level. The pad's output level should be adjusted in regards to how hard you hit the pad, to adjust the pad's dynamic range, or to better match the pad to the type of DTX Series Drum Trigger Module (DTXPRESS/DTX/DTXTREME) you are using. Level Adjustment Screw NOTE: When the PC3000A/130S/150S is used with a DTX Series Drum Trigger Module (DTXTREME/ DTX/DTXPRESS), enter the module's Trigger Edit Mode and set the [PAD Gain] (pad input level) parameter so that the display reads 90-95% when the pad is struck ff. Refer to the Owner's Manual that came with your module for more information. If the output level is too high, the pad's dynamic range (the difference between loud and soft tone) will be reduced and trouble such as double triggers (multiple triggers being produced by a single stroke) may occur. Do not put excessive pressure on the level adjustment knob, it may result in damage. Adjusting the Voice Volume To change the volume of the voice assigned to the PC3000A/130S/150S pad, use the [VOICE] edit mode in the DTX Series Drum Trigger Module. Please refer to the Owner's Manual that came with your module for more information. Replacing Worn Pads · After extended use, some of the parts used on the PC3000A/130S/150S will wear out or their quality will deteriorate (pad rubber, connecting jacks, etc. ). The life of these parts will vary depending upon the circumstances under which the PC3000A/130S/ 150S is used. · Please ask the dealer from whom you purchased the device about replacing worm parts. Part Names PC3000A PC3000AS Rotation Stopper Ribs Cup Connections PCY150S Rotation Stopper Ribs Using the supplied stereo phone cable, connect the output jack on the PC3000A/130S/ 150S to the input jack on the DTX Series drum Trigger Module (DTXTREME/DTX/ DTXPRESS). Insert the L-shaped connector into the output jack on the PC3000A/130S/ 150S. Output Jack Insert Pad Pad Edge Output Jack Pad Edge Output Jack Level Adjustment Knob Level Adjustment Knob (Switches are embedded in the edge section on the PC3000AS and edge and cup sections on the PCY150S) Setting Up First setup the rack system (Yamaha RS150, etc. ) or a commercially available cymbal stand (Yamaha CS series, etc. ) and then attach the PC3000A/130S/150S as shown in the illustration. Make sure that the pad is securely attached to the rack or stand. If the bolt is not tightened securely, the pad can slip or fall down causing injury. Is the module properly connected to a pair of headphones or an external audio device such as an amplifier, speaker, etc. ?Are module settings correct? What to check Refer to the previous [Connections] section and make sure that all connections are proper. Also, please refer to the Owner's Manual that came with your DTX Series Drum Trigger Module (DTXTREME/DTX/DTXPRESS) for more information regarding the problems described above and any other problems that you may be experiencing. If a solution can not be found to the problem after consulting the manuals, please contact the dealer from whom you purchased the product. Specifications PC3000A Cymbal Pad (13") PC3000AS Cymbal Pad (13") ø329 X 68(H) mm 1. 4kg Trigger Sensor (Piezo) x 1 Standard Monaural Phone Jack Trigger Sensor (Piezo) x 1 / Edge Switch x 1 Standard Stereo Phone Jack Size Weight Sensor System Output Jack If the Level Adjustment Screw is set too low, the single produced by the pad will be too low to produce sufficient volume from the drum trigger module's tone generator even though the pad is struck. Check the connections between the external device and the position of the power switch and volume level. PCY150S Cymbal Pad (15") Size ø386 X 70(H) mm 1. 8kg Trigger Sensor (Piezo) x 1 / Switch x 2 (Edge, Cup) Standard Stereo Phone Jack Check the volume setting of the voice assigned to the INPUT number to which the PC3000A/130S/150S is connected (refer to the previous "Adjusting the Voice Volume" section), or make sure the headphones volume level is not set too low, etc. Weight Sensor System Output Jack * Improvements may result in a change in the specifications and/or design of the product without notice. Hitting the pad once produces multiple sounds (Double trigger) Problem Is the level adjustment on the PC3000A/130S/150S set too high? What to check Too high of a the level adjustment setting causes the drum module to produce multiple sounds because the large signal produced by the high settings sustains for too long of a time. Refer to the "Output Level Adjustment" section described above to properly set the pad's output level. SPECIAL MESSAGE SECTION NOTICE: Service charges incurred due to a lack of knowledge relathing to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer's warranty, and are therefore the owners responsibility. Please study this manual carefuly and consult your dealer before requesting service. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: Warning: Do not attempt to disassemble. Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, plastics, etc. [. . . ] We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: Warning: Do not attempt to disassemble. Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly. [. . . ]