User manual YAMAHA PDM1

[. . . ] R PDM-1 INPUT INPUT SURROUND VOL VOL N R HIGH DEFINITION PLASMA MONITOR PICTURE PICTURE SOUND SOUND SET UP SET UP PICTURE POS. /SIZE ASPECT ASPECT PC PC OFF TIMER + ­ INPUT VOL POWE R / Y R - STANDB ON G POWER Operating Instructions English TQZW251 2 Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (6) The computer shown in the illustration is for example purposes only. (7) Additional equipment and cables shown are not supplied with this set. (8) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. 13 Connections Signal Names for D-sub 15P Connector Pin No. 1 2 3 4 5 Signal Name R G B GND (Ground) GND (Ground) Pin No. 6 GND (Ground) 11 7 GND (Ground) 12 8 GND (Ground) 13 9 NC (not connected) 14 10 GND (Ground) 15 Signal Name GND (Ground) SDA HD/SYNC VD SCL 11 12 13 14 15 6 1 7 2 8 3 9 10 4 5 Pin Layout for PC Input Terminal AV/Component/RGB/PC input signals AUDIO R AUDIO L VIDEO S VIDEO R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV IN COMPONENT/RGB IN PC IN SERIAL AV input AV input signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modified NTSC Component/RGB input horizontal frequency(kHz) 15. 734 15. 625 15. 734 15. 625 15. 734 horizontal frequency(kHz) 15. 734 15. 625 31. 468 31. 25 45 33. 75 28. 125 27 27 31. 5 31. 5 35 37. 5 31. 7 37. 9 46. 9 53. 7 49. 7 48. 4 56. 5 60 68. 7 68. 7 64 80 91. 1 75 vertical frequency(Hz) 59. 95 50 59. 95 50 59. 95 vertical frequency(Hz) 59. 94 50 59. 94 50 60 60 50 24 48 70 59. 94 67 75 60 60 75 85 75 60 70 75 85 75 60 75 85 60 PC RGB input Mark: Component/RGB/PC input signal name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 525 (480) /60i 625 (575) /50i 525 (480) /60p 625 (575) /50p 750 (720) /60p 1, 125 (1, 080) /60i 1, 125 (1, 080) /50i 1, 125 (1, 080) /24p 1, 125 (1, 080) /24sF 640 × 400 @70 640 × 480 @60 Macintosh13" (640 × 480) 640 × 480 @75 852 × 480 @60 800 × 600 @60 800 × 600 @75 800 × 600 @85 Macintosh16" (832 × 624) 1, 024 × 768 @60 1, 024 × 768 @70 1, 024 × 768 @75 1, 024 × 768 @85 Macintosh21" (1, 152 × 870) 1, 280 × 1, 024 @60 1, 280 × 1, 024 @75 1, 280 × 1, 024 @85 1, 600 × 1, 200 @60 Input signal can be displayed. RGB PC Component 14 Connections SERIAL Terminals connection The SERIAL terminal is used when the plasma display is controlled by a computer. 6 1 2 7 3 8 4 9 5 Pin layout for RS-232C Notes: (1) Use the RS-232C cable to connect the computer to the plasma display. (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the plasma display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Signal level Synchronization method Baud rate Parity Character length Stop bit Flow control RS-232C compliant Asynchronous 9600 bps None 8 bits 1 bit RS-232C Conversion cable D-sub 9-pin female Details 2 RXD 3 TXD GND 5 Non use 4·6 7 Shorted 8 NC 1·9 Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX End (03h) Command Command PON POF AVL AMT IIS Parameter None None Control details Power ON Power OFF Volume 00 - 63 Audio mute OFF Audio mute ON Input select (toggle) AV Mode Component / RGB mode (processed as a Y/PB/PR or RGB signals as set by this unit) PC Mode Screen mode select (toggle) 4:3 Zoom 16 : 9 Just Auto ** Start (02h) Colon Parameter(s) (1 - 5 bytes) 3-character command (3bytes) 0 1 None VID YP1 RG1 None NORM ZOOM FULL JUST SELF Notes: (1) If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. (2) If an incorrect command is sent by mistake, this unit will send an "ER401" command back to the computer. DAM With the power off, this display responds to PON command only. 15 Basic Controls R - STANDBY G POWER ON INPUT -- VOL + PDM-1 Main Power On/Off Switch Power Indicator The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) Stand-by . . . . Green INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press the "INPUT" button to select AV (S Video), Component/RGB and PC input signal modes sequentially. (see page 19) Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. · · · Stand-by (ON/OFF) button The plasma display must first be plugged into the wall outlet and turned on at the power switch (see page 18). Press this button to turn the plasma display On, from Stanby mode. Press it again to turn the plasma display Off to Stanby mode. Status button Press the "Status" button to display the current system status. AV 4:3 1 2 N button (see page 25, 26, 28, 29) Off timer 90 3 1 AV(S Video), Component/RGB, PC mode 2 Aspect mode (see page 22) 3 Off timer The off timer indicator is displayed only when the off timer has been set. PICTURE button (see page 28) PICTURE POS. /SIZE button (see page 24) PC button Press the "PC" mode selection button to select the PC mode. This button is used to switch directly to PC mode. 16 Basic Controls SURROUND button (see page 27) INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press to select AV(S Video), Component/RGB and PC input signal modes sequentially. (see page 19) Sound mute On/Off (see page 26) INPUT INPUT SURROUND Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. VOL VOL R button (see page 21) N R ACTION button Press to make selections POSITION buttons PICTURE PICTURE SOUND SOUND SET UP SET UP SET UP button (see page 20) PICTURE POS. [. . . ] V-Freq. 31. 5 kHz 60. 0 Hz 36 Troubleshooting Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Interference Sound Noisy Sound Checks Electrical Appliances Cars/Motorcycles Fluorescent light Normal Picture No Sound Volume (Check whether the mute function has been activated on the remote control. ) Not plugged into AC outlet Not switched on Contrast and Brightness/Volume setting (Check by pressing the Power Switch or stand-by button on the Remote Control. ) If a signal with a non-applicable colour system format, or frequency is input, only the input terminal indication is displayed. (see page 28, 29) Colour system (see page 35) No Picture No Sound No Picture Normal Sound No Colour Normal Sound Symptoms Game console picture or similar is distorted. Picture is distorted during the function of play, rewind, fastforward, or other operations of the VCR or similar. [. . . ]