User manual YAMAHA PF1500

[. . . ] Loose bolts may result in the rack overturning or parts dropping, causing injury. · Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. · When setting up the product, please pay close attention to the handling and setting of cables. [. . . ] · Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. · Watch your fingers when adjusting clamps. They may become pinched, resulting in injury. · Be careful around pipe ends, inside the pipe and screw ends. · Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. · Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. As shown below, ensure that the rod section is fully inserted into each pad's mounting hole, and then fully tighten the clamp bolt. Tom pad Clamp rod Rod section CH750 CH755 CH750 Insert Clamp bolt NOTICE · Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. · Do not step on or place heavy objects on the product. Alternatively, you can place the packages' cardboard boxes on the floor under the hi-hat stand and kick pad to protect it from damage. Module stand 8. Assemble the felt pad that came with your pad unit. Drum trigger module (back side) Front of module Connect the pads to the drum trigger module. As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module. 3. Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder's shaft. In such a case, loosen the key bolt as much as possible without removing it. * The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly of your pad unit. 9. Tighten the wing nut to secure the pad unit to the cymbal holder. Stopper's pin Wing nut 2. Place the module stand inside the holder clamp and tighten the clamp bolt to secure in position. 4. Replace the bolt cover. Bolt cover Felt pad that came with pad unit Insert the 10-channel snake cable's straight plugs into the drum trigger module's trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]). · If you are using the standard setup, the stickers on each of the snake cable's plugs will indicate the name of the corresponding pad. 2. Plug the 10-channel snake cable's L-shaped plugs into the correct pads. [Locations of pad jacks] Pad unit Smaller hole [Drum trigger module's rear panel] Drum trigger module + module stand Stopper Insert Clamp bolt Pad unit 10 9 8 7 6 5 4 3 2 1 Felt pad Cymbal holder Holder clamp Bolt cover Pin Straight plug names (as shown on stickers) DTX700 jack names 1: qSNARE 2: wTOM1 3: eTOM2 4: rTOM3 5: tRIDE 6: yCRASH1 7: uCRASH2 8: iHI-HAT 9: HI-HAT CONTROL 10: oKICK/!0 [10-channel snake cable] Straight plugs Stopper * When assembling the bolt cover, turn until it no longer rotates. Cymbal holder SNARE TOM1 TOM2 TOM3 RIDE CRASH CRASH2 HI HAT HH CON KICK 3. In the case of snare and tom pads, wrap the cables around the cable clips to preL-shaped plugs vent them from being pulled out. HH CON HI HAT KICK SNARE TOM1 CRASH TOM2 TOM3 RIDE CRASH2 Assembling the hi-hat stand NOTICE Excessive bending can damage the pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. [. . . ] As shown on the right, loosen the wing bolt (b in the figure) to remove the hi-hat clutch. * This hi-hat clutch is not used within the standard assembly example shown in this pamphlet. Instead, use the hi-hat clutch that came with your RHH135. Hi-hat clutch Felt washer 2. Loosen the hi-hat stand's wing bolt (a in the follow3. Extend the tripod legs to stabilize the stand. Retighten the wing bolt loosened in Step 2. 6 1. Connect the drum trigger module to a power supply. b Support plate 6. [. . . ]