User manual YAMAHA PF1500E

[. . . ] · Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. · If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. [. . . ] Carelessly placed cables may cause the user and others to trip and fall. Doing so may result in injury or damage/deterioration to the product. · Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. · Watch your fingers when adjusting clamps. They may become pinched, resulting in injury. · Be careful around pipe ends, inside the pipe and screw ends. may injure your fingers. Insert · Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. · Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. If necessary, use clamp bolts A to E to adjust the Mounting the snare pad Clamp bolt NOTICE · Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. 4 5 1. Position the hi-hat stand and kick pad as desired, referring to the standard assembly example on the other side. NOTICE Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard boxes on the floor under the hi-hat stand and kick pad to protect it from damage. Connect the pads to the drum trigger module. As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module. Module stand 8. Assemble the felt pad that came with your pad unit. Place the stopper on the cymbal holder. * The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly of your pad unit. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder's shaft. In such a case, loosen the key bolt as much as possible without removing it. Insert the 9-channel snake cable's straight plugs into the drum trigger module's trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]). · If you are using the standard setup, the stickers on each of the snake cable's plugs will indicate the name of the corresponding pad. 2. Plug the 9-channel snake cable's L-shaped plugs into the correct pads. [Locations of pad jacks] [Drum trigger module's rear panel] Drum trigger module (back side) Front of module 9. Tighten the wing nut to secure the pad unit to the cymbal holder. Stopper's pin Wing nut Felt pad that came with pad unit Pad unit Smaller hole 4. Place the module stand inside the holder clamp and tighten the clamp bolt to secure in position. Bolt cover 9 8 7 No 6 Connection 5 4 3 2 1 Straight plug names (as shown on stickers) DTX700 jack names 1: qSNARE 2: wTOM1 3: eTOM2 4: rTOM3 5: tRIDE 6: yCRASH1 7: iHI-HAT 8: HI-HAT CONTROL 9: oKICK/!0 Pad unit Stopper [9-channel snake cable] Straight plugs Drum trigger module + module stand Felt pad Insert Cymbal holder Bolt cover Pin L-shaped plugs SNARE TOM1 TOM2 TOM3 RIDE CRASH HI HAT HH CON KICK 3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being pulled out. HH CON HI HAT CRASH KICK SNARE TOM1 TOM2 TOM3 RIDE Stopper Clamp bolt Holder clamp * When assembling the bolt cover, turn until it no longer rotates. Cymbal holder NOTICE Excessive bending can damage the pad cables. [. . . ] Instead, use the hi-hat clutch that came with your RHH135. Hi-hat clutch Felt washer Connect the drum trigger module to a power supply. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. ing figure). 1. b Support plate Insert the power adaptor's DC plug into the connector. Hook the power adaptor's cord around the cord clip to secure it in place. 2. Loosen the hi-hat stand's wing bolt (a in the follow3. [. . . ]