User manual YAMAHA PLG150PFE

[. . . ] Piano Plug-in Board Piano Plug-in Board Carte Plug-in piano Owner's Manual Bedienungsanleitung Mode d'emploi Precautions q Do not expose the plug-in board to direct sunlight, excessive humidity, high temperatures, excessive dust or strong vibrations. q Before handling the plug-in board, be sure to touch a metal surface to discharge any static electricity which may be in your body. q When holding the plug-in board, do not touch the inside area of the circuit board or apply excessive pressure to the board, and be sure to protect the board from contact with water or other liquids. q Before installing the plug-in board onto a tone generator/sound card, unplug the power connector of your computer. [. . . ] 1. 2. 13 Release Time This message adjusts the EG release time that was specified by the sound data. Control# 72 Parameter Release Time Data Range 0. . . 64. . . 127 (-64. . . 0. . . +63) 1. 2. 5 Main Volume This message controls the volume of each part. (It is used to adjust the volume balance between parts. ) Control# 7 Parameter Data Range Main Volume0. . . 127 Since this is a relative change parameter, it specifies an increase or decrease relative to 64. Increasing this value will lengthen the release time that follows a noteoff. 1. 2. 14 Attack Time This message adjusts the EG attack time that was specified by the sound data. Control# 73 Parameter Attack Time Data Range 0. . . 64. . . 127 (-64. . . 0. . . +63) When the Multi Part parameter Rcv VOLUME = OFF, that part will not receive Main Volume. With a value of 0 there will be no sound, and a value of 127 will produce the maximum volume. 1. 2. 6 Panpot This message controls the panning (stereo location) of each part. Control# 10 Parameter Pan Data Range 0. . . 64. . . 127 Since this is a relative change parameter, it specifies an increase or decrease relative to 64. Increasing this value will make the attack more gradual, and decreasing this value will make the attack sharper. 1. 2. 15 Brightness This message adjusts the cutoff frequency of the low pass filter specified by the sound data. Control# 74 Parameter Brightness Data Range 0. . . 64. . . 127 (-64. . . 0. . . +63) When the Multi Part parameter Rcv PAN = OFF, that part will not receive Panpot. 0 is left, 64 is center, and 127 is right. 1. 2. 7 Expression This message controls expression for each part. It is used to create volume changes during a song. Control# Parameter Data Range 1l Expression0. . . 127 If the Multi Part parameter Rcv EXPRESSION = OFF, that part will not receive Expression. Since this is a relative change parameter, it specifies an increase or decrease relative to 64. Lower values will produce a more mellow sound. For some sounds, the effective range may be less than the possible range of settings. 35 MIDI Data Format 1. 2. 16 Data Increment/Decrement (for RPN) This message is used to increment or decrement values for parameters specified by RPN (see 1. 2. 18), in steps of 1. Control# Parameter 96 RPN Increment 97 RPN Decrement The data byte is ignored. Data Range -- -- 1. 2. 19 Assignable controller By assigning a control change number of 0. . . 95 to a part, application of effects can be controlled. [. . . ] Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-703-0900 BRAZIL Yamaha Musical do Brasil LTDA. Rebouças 2636, São Paulo, Brasil Tel: 011-853-1377 DENMARK YS Copenhagen Liaison Office Generatorvej 8B DK-2730 Herlev, Denmark Tel: 44 92 49 00 PHILIPPINES Yupangco Music Corporation 339 Gil J. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 ARGENTINA Yamaha Music Argentina S. A. Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-371-7021 FINLAND F-Musiikki Oy Kluuvikatu 6, P. O. [. . . ]