User manual YAMAHA PM1000E

[. . . ] 11 Additional functions for the USER DEFINE switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Inserting MIDI events from the event list . . . . . 12 CLEAR ALL button added to the OSCILLATOR and TALKBACK screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Outputting the MONITOR and CUE signals from the DSP1D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Displays the time code. 3 CUE These buttons enable you to switch cue monitoring on/off for the channels and DCA groups. They are linked with the [CUE] key of the corresponding channel or DCA group. Displaying the GEQ routings When you select a GEQ module in the GEQ PARAMETER screen, the GEQ SELECT pop-up window enables you to identify any GEQ modules that have already been patched. 4 DISPLAY CH Switches the channels that are shown in the FADER VIEW screen. · When you are using the IN CH View function: INPUT [PANEL] Channels specified via the Panel Assign function, and DCA groups 1­12 Input channels 1­48, ST IN channels 1­4, DCA group 1­12 Input channels 49­96, ST IN channel 5­8, DCA groups 1­12 CH 1-48/ST IN 1-4 CH 49-96/ST IN 5-8 · When you are using the OUT CH View function: MIX 1-48 MIX channels 1­48, STEREO A/ B channels, DCA groups 1­12 MATRIX channels 1­24, STEREO A/B channels, DCA groups 1­12 MATRIX This window displays the signal routing of already-patched GEQ modules, and displays "NO ASSIGN" for unpatched GEQ modules. 8 Changes and additions of screens Displaying the GR meters The INPUT GR screen and OUTPUT GR screen have been added to the Meter function. These screens display the gain reduction meters for Input channel gates and compressors, and Output channel compressors. INPUT GR OUTPUT GR 4 Pair icon This icon indicates the pairing status of two adjacent oddnumbered/even-numbered channels. 1 3 4 3 2 1 DISPLAY CH Switches the channels that are displayed in the INPUT GR and OUTPUT GR screens. INPUT GR screen: CH 1-48/ST IN 1-4 CH 49-96/ST IN 5-8 Input channels 1­48, ST IN channels 1­4 Input channels 49­96, ST IN channels 5­8 OUTPUT GR screen: MIX 1-48 MATRIX 1-24/STEREO MIX channels 1­48 MATRIX channels 1­24, STEREO A/B channels 2 GATE/COMP (Gate/Compressor) These buttons select whether the meters will display gain reduction for the Gate or Compressor. These buttons appear only in the INPUT GR screen. 3 Meters These peak level meters indicate the amount of gain reduction for each channel. The current fader value is shown in the box below. Changes and additions of screens 9 Other changes Filtering during save or load operations You can specifically select any region of any scene or library data to be saved to a memory card. You can also specifically select any region of any scene or library data to be loaded from a memory card. LOAD/SAVE be saved or loaded. If you want to change the save/load destination numbers, click the [ ]/[ ] buttons at the left and right of the starting number box or use the [DATA] encoder. (The value in the ending number box will change automatically according to the starting number and the source range. ) When you change the save destination starting number: 1 2 3 4 CS1D Memory card Starting number Ending number 01. 0 01. 1 01. 2 01. 3 01. 4 01. 5 AAA BBB CCC DDD EEE FFF Starting number SAVE 02. 0 02. 1 02. 2 02. 3 02. 4 AAA BBB CCC DDD EEE SOURCE DESTINATION In addition to BASIC mode (in which you can save the entire or specified data in the scene memories or libraries to a memory card, or load them from a memory card), ADVANCED mode enables you to save or load a specified range of the data. When you change the load destination starting number: ADVANCED mode: When you turn on the ADVANCED button in the LOAD/SAVE screen, the left side of the screen will display the following items: Memory card Starting number Ending number 02. 1 02. 2 02. 3 02. 4 02. 5 BBB CCC DDD EEE FFF CS1D 1 MODE Starting number LOAD 02. 5 02. 6 02. 7 02. 8 BBB CCC DDD EEE Switches between BASIC and ADVANCED mode. SOURCE DESTINATION 2 CATEGORY Indicates the category of data that is selected for saving or loading: scene memory or a type of library. Click the [ ]/ [ ] buttons at left and right or use the [DATA] encoder to change the category. Note · To format a memory card first, use a computer or other external device and select the FAT16 format. The USER DEFINE switch LED flashes at the specified tempo while and after you set the tempo. For more information on the Tap Tempo function, please refer to page 51 of the PM1D System Software Version 1. 5 Supplementary Manual. Other changes 11 Inserting MIDI events from the event list In addition to entering hexadecimal values, you can also specify MIDI events for scene recall by entering the desired MIDI events using the list in the new MIDI EVENT SETUP pop-up window. To open this pop-up window, a MIDI EVENT button has been added to the SCENE STORE pop-up window and the SCENE TITLE pop-up window. You can also delay the output of MIDI events by a specified time. When you click a box in which a hexadecimal value has been input, the range of values that can be interpreted as a valid MIDI message (including that box) will turn red. The lower part of the window displays the MIDI channel (MIDI CH), message type (TYPE), and data values (DATA 1, DATA 2) that are interpreted from this MIDI message, enabling you to verify that the appropriate MIDI message has been input. You can use the following buttons to input or edit the message in this window. [ ]/[ ]buttons Move the highlighted area to left or right. Inserts a space (blank) at the highlighted position. Pressing the <Insert> key on a PS/2 keyboard will produce the same result. Deletes the character at the highlighted position. Pressing the <Delete> key on a PS/2 keyboard will produce the same result. Erases the entire message that was input in the MIDI message input boxes. INS button DEL button CLEAR button 2 Specifying the type of message 1. [. . . ] This value applies only when the effect type is REV-X PLATE, with ROOM SIZE set to 28. The setting range varies depending on the effect type and the ROOM SIZE value. 075: COMP276 This effect emulates the characteristics of analog compressors that are widely used in recording studios. It will produce a thick, strong frame sound suitable for drums and bass. You can control two monaural channels independently. Parameter INPUT 1 OUTPUT 1 RATIO 1 ATTACK 1 RELEASE1 MAKE UP1 Range ­180 to 0 dB ­180 to 0 dB 2:1, 4:1, 8:1, 12:1, 20:1 0. 022­50. 4 ms 10. 88­544. 22 ms OFF, ON Description Adjusts the CH1 input level Adjusts the CH1 output gain Ratio for CH1 compressor Attack time for CH1 compressor Release time for CH1 compressor Automatically corrects output gain reduction when CH1 compressor is applied When the HPF in the side chain of the CH1 compressor is turned on, the compression applied to the low range will be weakened, thus emphasizing the low range. [. . . ]