User manual YAMAHA PM1DV14

[. . . ] PM1D System Software V1. 4 Supplementary Manual E Contents New functionality in system software V1. 4 . 3 Digital gain for input channels / insert inputs . 6 BALANCE control for input channels / ST IN channels . 8 Temporary monaural setting for paired input channels / ST IN channels . [. . . ] Only the channel that is not set to Recall Safe will be recalled. In the case of LMONO, recalling the R channel will cause that channel to be recalled in an Off state. In the case of LMONO, recalling the L channel will cause that channel to be recalled in an Off state. · If you recall channel library no. 00, these temporary monaural settings will be the same as for unpaired channels. In other words, the PAN mode will remain as it was, and the PAN/BALANCE will be set to the center. For paired channels, the PAN mode will be forced to INDIVIDUAL, and operation will be the same as in software version 1. 30. · The fade time will operate according to the pair on/ off setting, without being affected by this temporary monaural setting. When paired, the fade time of the two channels will be linked. · Insert on/off, insert point, and direct point can now be set separately for L/R even if one of the temporary monaural modes L-MONO/R-MONO/LR-MONO are selected. (This setting is stored in the scene memory. ) · If a channel library is recalled to the channel that is forced off by a L-MONO or R-MONO setting (i. e. , the R channel in the case of L-MONO, or the L channel in the case of R-MONO), the recalled channel will be forced off. · The KEY IN link for GATE or COMP will not be changed by any of these temporary monaural settings. LINK will be turned on only if monaural is changed to pair. LINK will not be turned off when the setting is changed from pair to link. 12 Temporary monaural setting for paired input channels/ST IN channels If PAN is changed: PAN*1 BALANCE MONO mode PAIR PAIR mode L-MONO R-MONO *1: *2: BALANCE PAN . *1 · BALANCE will be CENTER. *2 · The PAN that is sent to a MIX bus that is both paired and VARI-type will change to BALANCE, and set to CENTER. · The L channel PAN will be set to far left, and the R channel PAN will be set to far right. *2 · The BALANCE that is sent to a paired VARI-type MIX bus will change to PAN, and panned to left and right as above. PAN refers to any of the pan modes INDIVIDUAL PAN, GANG PAN, or INVERTED GANG PAN. This is the operation that occurs when the PAN MODE is changed in the screen. If it is changed by a scene recall, it will follow the stored PAN/BALANCE setting. If PAIR is changed: Cancel pairing Specify pairing Paired Pairing defeated · PAN setting remains as is. *1: PAN refers to any of the pan modes INDIVIDUAL PAN, GANG PAN, or INVERTED GANG PAN. Paired L-MONO L-MONO Paired · The PAN value of the L/R channels and the PAN MODE setting will be temporarily preserved. · The L/R channel PAN will be CENTER. *2 · PAN to a paired VARI-type MIX bus will also be set to CENTER. · The R channel ON/OFF will be turned OFF, and cannot be turned ON. · The BALANCE value of the L/R channels and the PAN MODE setting will be temporarily preserved. · The L/R channel PAN will be CENTER. *2 · BALANCE to a paired VARI-type MIX bus will change to PAN, and set to CENTER. · The R channel ON/OFF will be turned OFF. (Cannot be turned ON. ) · PAN MODE will be set to INDIVIDUAL PAN. *1: *2: *3: · The PAN/BALANCE value of the L/R channels and the PAN MODE will return to the settings that were in effect when the channels were paired. *2 · PAN to a paired VARI-type MIX bus will change to PAN or BALANCE, and will be set to the same value as the temporarily preserved PAN value for TO ST. · R-channel parameters other than PAN will be set identically to the L channel. *3 PAN refers to any of the pan modes INDIVIDUAL PAN, GANG PAN, or INVERTED GANG PAN. [. . . ] Press a MODE button (INPUT 1-48, INPUT 49-96, MIX, MATRIX) so that the desired channels appear in the screen. Click the ON button of the channels for which you want to use tracking. At this point, the fader position of a channel that you have turned on by clicking will be memorized as the reference position. Thus, the offset value will be set to 0. Hint In this example, the Tracking function was enabled in step 5. [. . . ]