User manual YAMAHA PM3500

[. . . ] Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. [. . . ] · When the ALL INPUT button is on The Fade function will apply to the PAN (BALANCE) parameter of all input channels. · When the SAME AS FADING button is on The Fade function will apply to the PAN (BALANCE) parameter of only the input channels you select in 4. C FADE TIME/START OFFSET Use the following two buttons to select the parameters that can be viewed/edited in the FADE TIME screen. The indication at the right shows which button is currently selected. · When the FADE TIME button is on Edit the time (fade time) over which the fader or pan parameter of the corresponding channel will reach the new value when you recall a scene for which the Fade function is enabled. 184 PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section F CLEAR ALL This button disables the Fade function for all input channels or output channels. 4 D Channel settings 56 In this window, select the copy-destination item and click the OK button; the value of the selected channel will be copied. PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section 185 Appendices Input functions Here you can turn the Fade function on/off and specify the fade time (or the start offset time) for each input channel / output channel. Use the channel name buttons to switch the Fade function on/off. The box below each button lets you specify the fade time or start offset time. Move the cursor to a box, and turn the [DATA] encoder or click the / buttons at the left and right to edit the value. The color of the numerical value shown in the box will change as follows. · When the FADE TIME button is on The value is displayed in white for channels whose start offset time is "----" (unset), and in light blue for channels that are set to 0. 1 or above. · When the START OFFSET button is on The value is displayed in red for channels whose start offset time is "----" (unset), and in yellow for channels that are set to 0. 1 or above. If desired, you can copy the fade time / offset time value from one channel to another as follows. · GATE STEREO LINK · COMP STEREO LINK · DELAY GANG · PAN MODE · GEQ LINK · ATT GANG · MS DECODE · FIXED/VARI Note · Paste is valid even in PREVIEW mode. · When you paste to a scene, there may be cases in which a conflict in pairing settings causes the settings of a parameter to differ between L and R channels. In such cases, the parameter will be recalled with those settings, and will be linked when it is next operated. A MODE Here you can select the way in which program changes and control changes will be transmitted/received. · PROGRAM CHANGE MODE In this area you can select the program change transmission/reception method. SINGLE If this button is on, program changes will be transmitted/received on a single MIDI channel (Single mode). OMNI ON/OFF If this button is on, program changes of all MIDI channels will be received in Single mode (this is unavailable in Multi mode). 188 PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section BANK ON/OFF If this button is on, bank select messages will be transmitted and received in Single mode (this is unavailable in Multi mode). MULTI If this button is on, program changes will be transmitted/received on multiple MIDI channels (Multi mode). Hint · If program change reception is on, the PM5D's scenes or effects will switch when the appropriate program change is received from an external device. Additionally, if transmission is on, program changes will be transmitted to an external device when scenes or effects are switched on the PM5D. · The scene/effect assignment for each program change number is made in the MIDI PGM CHANGE screen ( p. 190). · Hint · If control change reception is on, the PM5D's parameters will change when the appropriate control change is received from an external device. If transmission is on, a control change will be transmitted to an external device when you edit a parameter on the PM5D. [. . . ] Input [+30dBu] INSERT IN IN IN IN IN Max. Output [+24dBu] +30 +24 +20 +10 +4 0 -10 -20 -30 Nominal [+10dBu] Input OUT OUT OUT OUT OUT OUT OUT Nominal Output [+4dBu] default setting OMNI OUT1-24 Max. Input [-42dBu] CASCADE IN*1 CASCADE OUT*1 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 Max. DSP Noise Floor *1 CASCADE TYPE = PM5D - PM5D, PM5D - DSP5D *2 CASCADE TYPE = PM5D - DCU5D --- DCU5D - PM5D, PM5D - DCU5D --- DSP5D, PM5D - DSP5D - DSP5D, PM5D - DCU5D --- DSP5D - DSP5D, PM5D - DCU5D --- DSP5D - DCU5D --- DSP5D INPUT 1-48 (GAIN MIN. ) ST IN (GAIN MIN. ) INPUT 1-48 (GAIN MAX. ) ST IN (GAIN MAX. ) Nominal [-62dBu] Input -170 -180 -190 [0dBu = 0. 775Vrms] [0dBFS = Full Scale] For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. [. . . ]