User manual YAMAHA PM5D

[. . . ] PM5D/PM5D-RH V2 DSP5D Owner's Manual EN FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. [. . . ] Use the channel name buttons to switch the Fade function on/off. The box below each button lets you specify the fade time or start offset time. Move the cursor to a box, and turn the [DATA] encoder or click the / buttons at the left and right to edit the value. The color of the numerical value shown in the box will change as follows. · When the FADE TIME button is on The value is displayed in white for channels whose start offset time is "----" (unset), and in light blue for channels that are set to 0. 1 or above. · When the START OFFSET button is on The value is displayed in red for channels whose start offset time is "----" (unset), and in yellow for channels that are set to 0. 1 or above. If desired, you can copy the fade time / offset time value from one channel to another as follows. Move the cursor to the box that displays the value you want to copy; then hold down the [SHIFT] key and press the [ENTER] key to access the JOB SELECT window. Output functions Global functions Function menu Information shown in the display · When the START OFFSET button is on Edit the time (start offset time) after which the fader or pan parameter of the corresponding channel will begin changing when you recall a scene for which the Fade function is enabled. E SET ALL This button enables the Fade function for all input channels or output channels. SCENE function TRACKING RECALL screen Here you can make settings for the Tracking Recall function, which adds a specified offset value to the value of each fader when you recall a scene. TRACKING RECALL 6 7 F ON (Tracking On) These buttons enable/disable tracking for each channel. If the TRACKING RECALL ENABLED/ DISABLED button is set to ENABLED, tracking is enabled on channels for which this button is ON. Note If OFFSET LOCK (5) is off, turning this button on will reset the tracking offset of the corresponding channel to 0 dB. If in this state you operate the fader of the corresponding channel, the relative amount of fader movement from the point at which this button was turned on will be memorized as the tracking offset. You can then turn OFFSET LOCK on to lock the offset. This offset value will be added whenever you subsequently recall a scene. 4 3 G Tracking offset Here you can specify the offset value applied to each channel if tracking is enabled. While OFFSET LOCK (5) is off, operating the panel faders will cause these values to change as well; however, adjusting the offset values in the screen will not cause the panel faders to move. 1 2 5 A TRACKING RECALL ENABLED/DISABLED Enables/disables the Tracking Recall function. Hint The settings in the TRACKING RECALL screen apply to all scenes. B DISPLAY SELECT These buttons select the type of channels that are shown in the TRACKING RECALL screen; either INPUT (input channels) or OUTPUT (output channels). C SET ALL This button enables Tracking Recall for all channels (including channels not currently shown in the screen). D CLEAR ALL This button disables Tracking Recall for all channels (including channels not currently shown in the screen). E OFFSET LOCK If this button is on, the sliders of all channels (including channels not currently shown in the screen) will be grayed-out, and you will be unable to edit the offset value. 186 PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section This screen lets you copy parameter settings of any desired channel or parameter in the current scene, and paste them into one or more scenes in scene memory. GLOBAL PASTE ALL ATT EQ GATE COMP DELAY FADER ON PAN/BAL INSERT SEND*1 DCA MUTE LCR HA PATCH All parameters except for HA, PATCH, and NAME Attenuator EQ function settings GATE function settings COMP function settings DELAY function settings Fader level CH [ON] key on/off status Pan/balance settings Insert on/off status and insert point Send level to the desired MIX bus(es) Associated DCA group LCR screen settings Settings for the head amp assigned to the corresponding input channel Settings for the input patch assigned to the corresponding input channel Name assigned to the corresponding input channel 1 NAME A PASTE MODE Select the type of copy-source parameter from the following choices. You cannot select more than one type simultaneously. Output channel parameters DCA, GEQ, EFFECT . DCA level or mute on/off status, GEQ settings, internal effect settings · If Paste Mode= OUTPUT Select output channels in the left area, and select parameters in the right area. You can select the following parameters. EQ COMP DELAY FADER ON BAL INSERT TO MTRX*1 DCA MUTE LCR EQ function settings COMP function settings DELAY function settings Fader level CH [ON] key on/off status Balance settings Insert on/off status and insert point Send level to the desired MATRIX bus(es) Associated DCA group Associated mute group LCR screen settings Selects whether the send level sent from input channels to the selected MIX bus will be included (WITH. . . ) or will not be included (WITHOUT. . . ) in the pasted data. 2 WITHOUT MIX SEND/ WITH MIX SEND *1. If the TO MTRX button is on, use the MATRIX buttons (1­8) to select the applicable MATRIX bus. Note · If Paste Mode= INPUT, and the parameter being pasted is NAME, the name library linked to the selected scene will be searched automatically and pasted. · Be aware that if other scenes link to this library, the paste operation will overwrite the library, meaning that other scenes may be affected. B CURRENT SCENE Here you can select the channels and parameters that will be copied from the currently selected scene. The contents shown in this area will depend on the paste mode (1) you choose. PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section 187 Appendices Input functions Output functions *1. [. . . ] Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Europe GmbH Branch Sp. z o. o. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]