User manual YAMAHA PS200E

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] The unit starts up in the "normal" mode if the power is turned on while the MEMORY [D] button is not held. PS200E Manager Mode This mode allows communication with the PS200E application. Communication with AMX and similar external controllers cannot occur in this mode. This is the unit's normal operating mode. Communication with AMX and similar external controllers is also possible in this mode. Communication with the PS200E Manager application is not possible in this mode. 7 [SIGNAL/PEAK] Indicators These indicators light green when a signal is detected at the corresponding stereo input. The [SIGNAL/PEAK] indicators also light red to indicate excessive input level at the corresponding input. If excessive input level is indicated, reduce the output level of the connected source. NOTE · The [SIGNAL/PEAK] indicator may light red when certain types of signals are received via the OPTICAL input, but in such cases the signal is within range and no further adjustments are required. 8 Level Knobs These knobs adjust the input level of the corresponding stereo channels. Normal Mode # [POWER] Switch & Indicator Turns power to the unit ON or OFF. The indicator lights green when the power is ON. NOTE · Since the level settings for each channel are stored in the PS200E unit itself, be sure that the PS200E Manager application is online when setting up the memories. PS200E Owner's Manual 9 Controls and Functions Rear Panel NOTE · Refer to "Connectors and Cables" on page 13 for details on connectors and cables for use with the PS200E. 1 3 5 7 8 9 2 4 6 ) 1 [AC IN] Connector Connect the supplied AC cable here. First connect the AC cable to the PS200E, then plug it into an appropriate AC outlet. STEREO INPUT Section 5 L/R Connectors 1, 2, 3, 4A, and OPTICAL 4B The output from CD players and other stereo line-level sources can be connected to these stereo inputs. 2 Earth Screw For maximum safety, please earth the unit properly. The supplied AC power cable is a 3-wire type, so if the AC outlet used is properly earthed the PS200E will be earthed as well. With a Euroblock connection, the stranded wire may be prone to breakage because of metal fatigue due to the weight of the cable or due to vibration. When rack-mounting your equipment, use a lacing bar when possible to bundle and fasten the cables. · If cables will be frequently connected and 1. 6 mm or less disconnected, as in the approx. 7 mm case of a portable installation, we recommend that you use ferrules with insulation sleeves. Use a ferrule whose conductor portion has an external diameter of 1. 6 mm or less, and a length of approximately 7 mm (such as the AI0, 5-6WH made by the Phoenix Contact corporation). Use balanced lines to connect microphones and similar sources to the [MONO INPUT] connectors. Wire balanced cables as shown in the diagram below. XLR-3-11C (or equivalent) 1 3 2 2 1 3 · CAUTION If you use stranded wire, do not tin (plate with solder) the exposed end. When an amplifier to be connected to the OUTPUT connector has balanced XLR type inputs, wire the connection cable as shown in the diagram below. XLR-3-12C (or equivalent) 1 · Loosen the terminal screws. NOTE A "minus" type screwdriver with a blade width of approximately 3 millimeters is recommended for Euroblock connector attachment. 3mm 1 3 2 1 2 3 Loosen Slotted screwdriver Terminal screw Euroblock plug 2 Insert the cables. PS200E Owner's Manual 13 Connections 3 4 Securely tighten the terminal screws. Pull the cables (not too strongly) to confirm that they are securely connected. Connect the Euroblock plug to the PS200E Euroblock connector. [GPI] Connector (25-pin D-sub) External GPI (General Purpose Interface) control devices can be connected to this connector to allow input and output of remote control signals. The PS200E GPI port has eight inputs and eight outputs, plus a dedicated "POWER MONITOR" output that indicates the unit's ON/OFF status. Shorting an input pin to ground (GND) recalls the corresponding memory number. The output pins are open-collector outputs that deliver a maximum output of +35 volts, with a maximum current capability of 30 mA per port. [. . . ] For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]