User manual YAMAHA PSR-100E

[. . . ] We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: Battery Notice: This product MAY contain a small nonrechargable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. [. . . ] The higher the value the greater the chorus depth. DSP EFFECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use the TYPE LCD [v/w] controls to select a DSP EFFECT type, and the DEPTH LCD [v/w] control to set the depth of the selected DSP effect. For some DSP effect types the DEPTH parameter is fixed at "100" and cannot be changed. NOTES · Depending upon the selected DSP EFFECT type, some PAN parameters may not function. 87 Custom Voice Edit STORE/CLEAR s STORE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stores the edited custom voice data in the specified custom voice memory location. When this function is selected the size of the current voice and the remaining memory capacity available for voice storage are displayed to the right of the display. The names and sizes of all other voices currently in memory are shown in the lower section of the display. ZSelect a Custom Voice Number Use the STORE LCD [v/w] controls to select the custom voice number to which you want to store the newly created custom voice. XStore the Custom Voice Press the EXECUTE button, then press YES to store the voice when the confirmation display appears (or NO to cancel). s CLEAR CUSTOM VOICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clears unwanted custom voices from memory, making more memory available for custom voice storage. ZSelect a Custom Voice Number Use the CLEAR LCD [v/w] controls to select the custom voice you want to clear. XClear the Custom Voice Press the EXECUTE button, then press YES to clear the voice when the confirmation display appears (or NO to cancel). 88 Custom Voice Edit The Drum Kit Edit Mode When a drum kit voice is selected for editing the parameters and functions available are essentially the same as those for the orchestra voices in the FULL EDIT mode. Many parameters of individual percussion voices within the DRUM KIT can be edited independently. The only differences are in the E1:BASIC display: q Use the PERCUSSION parameter function to select the desired percussion sound for editing. Pressing any key on the keyboard will directly select that keys percussion sound. q The drum kit voices have no VOLUME or KEY ON DELAY parameters. q The PITCH parameter functions in the same way as the TUNE FINE parameter provided for the orchestra voices. The E2:CONTROLLER, E3:ENVELOPE, E4:EFFECTS, and STORE/CLEAR display parameters and functions are the same as in the orchestra voice FULL EDIT mode. NOTES · Some parameters may not effect the drum kit voices in exactly the same way as the orchestra voices. · Some settings may result in no sound, depending on the drum kit voice and parameter. · The SUSTAIN parameter cannot be changed in the E3 setting. 89 Disk Operations The PSR-100E [DISK] button accesses a range of functions that are used for storage and retrieval of floppy disk data. If you want to execute the load operation press the YES LCD button (or press the NO LCD button to cancel the operation). "Don't remove disk" will appear while the data is being loaded, and the progress of the load operation will be indicated by a bar graph on the display. NOTES · Data spanning two or more disks (i. e. "split" data) cannot be loaded by using the INDIVIDUAL LOAD function. · When loading CUSTOM STYLE or CUSTOM VOICE data -- not in the INDIVIDUAL mode -- all data will be loaded even if the loaded file contains empty styles or voices. · In the case of the custom style load function, SFF (optional style file format) disks can also be loaded. 91 Disk Operations Save To Disk Saves the data listed below to a floppy disk inserted into the PSR-100E disk drive. NOTES · If an unformatted disk or a disk which has not been formatted for use with the PSR-100E is inserted, the "Wrong disk type or format!Format disk?" confirmation message will appear when the SAVE TO DISK function is selected. Press YES to format the disk or NO to cancel. If the FILE LIST display shown to the right is not showing, press the LIST LCD button to select it. Use FILE LCD [v/w] controls to select the file to which you want to save the data. The file list at the bottom of the display includes all files which currently exist on the disk and one "*** NEW ***" file. Select an existing file if you want to overwrite the file with the new data, or select the "*** NEW ***" file if you want to create a new file. With the exception of the "*** NEW ***" file, the size of each file will appear to the right of the file name in kilobytes (approximate). [. . . ] Benches supplied by Yamaha are designed for seating only. 14. 6. 7. 15. PLEASE KEEP THIS MANUAL 92-469-2 FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. [. . . ]