User manual YAMAHA PSR-41E

[. . . ] 21 Internet Connection Guide 1 Selection of the Connection Environment To connect the instrument to the Internet, a full-time online connection (ADSL, optical fiber, cable Internet, etc. ) using a broadband router or a modem equipped with a router is necessary. NOTE · Since no broadband router or modem settings can be made by the instrument itself, use a computer to make the settings before connecting to the instrument. · Since this instrument does not support PPPoE communication, it is not possible to directly connect to the modem without a router. · Dial-up and ISDN connections cannot be used. Depending on the Internet connection, the number of connectable devices may be limited. This may mean that your instrument cannot be connected to the Internet. [. . . ] Check whether your USB wireless LAN adaptor supports WPS by accessing the URL of "Required Devices" on page 6. Press the [B] button to select "Setup by WPS (push button), " then press the [G] button to proceed to "NEXT. " Proceed to step 8. Setup after searching for wireless networks When the list of the access points near the instrument is displayed, select the access point to be used. The SSID, channel and security format of the selected access point are automatically set. When the security is set, input the key. Press the [C] button to select "Setup after searching for wireless networks, " then press the [G] button to proceed to "NEXT. " Proceed to step 9. NEXT PAGE Internet Connection Guide 8 Connection 8 Press the [F](YES) button, then within 2 minutes hold down the WPS button of the access point with router. For details about the operations in the setting of the access point on the router side, read the owner's manual for the product you are using. Proceed to step 13. 9 Use the [DATA ENTRY] dial to select the desired access point, then press the [G] button to proceed to "NEXT. " The SSID, channel and security format of the selected access point are automatically set. An access point that is security-enabled is displayed with a padlock icon " , " Input the key. Make sure that the settings are the same as those for the access point on the router side. NOTE · For details on confirmation and changes in the setting of the access point on the router side, refer to the owner's manual for the product you are using. Signal strength The signal strength may not be displayed depending on the particular USB wireless LAN adaptor you are using. With padlock icon " " Since the security is set to your access point with router, proceed to step 10, then input the key. No padlock icon If your access point with router has not been security-enabled, you don't need to make a setting for the wireless LAN. If you want to set the security to the access point, change this in the settings of your access point with router. NEXT PAGE Internet Connection Guide 9 Connection 10 Press the [D](KEY) button to call up the character-entry display to input the key. 11 Input the key. Refer to the Owner's Manual for character-entry details. To cancel the key input, press the [8t](CANCEL) button. 12 Press the [G](NEXT) button to set the key input. When you set the key input, the characters are hidden and displayed as "******. " Make a written note of the settings, in case you have to enter them again. SSID Access point Channel Security setting Security format Key YES NO -- -- NEXT PAGE Internet Connection Guide 10 Connection 13 Press the [G](CONNECTION) button to check the connection to the special website. The settings are saved by checking the connection. NOTE · Because the settings are lost when you turn off the power of the instrument, be sure to save the settings and changes you made. 14 Press the [G](DONE) button to connect to the special website. When the special website appears, the network settings to the Internet are complete. When the special website does not appear, refer to "Connection Help" on page 19. For details on operations in the special website, refer to the Owner's Manual. Internet Connection Guide 11 Connection Wireless LAN Connection Using Wireless Game Adaptor 1 Connect the devices according to the example. First turn the power of the instrument off, then connect the devices as shown in the illustration below, and finally turn the power on again. NOTE · For an illustration of the location of the LAN terminal, refer to the Owner's Manual. Set the instrument within 10­20 m from the access point. The signal will not be received if there is an obstacle blocking reception. Modem LAN terminal Internet LAN cable Wireless game adaptor Access point with router Required Devices · · LAN cable Wireless game adaptor For a list of wireless game adaptors whose compatibility has been confirmed by Yamaha, refer to the website: http://music. yamaha. com/download/ Access point with router (The router capability here is unnecessary if your modem has router capability. ) Modem (ADSL modem, optical network unit or cable modem) NOTE · The wireless game adaptor requires connection to the AC outlet. Short for Local Area Network, this is a data-transfer network that connects a group of computers at a single location (such as an office or home) by means of a special cable. Location information in other sentences and images, etc. that are under buttons and character strings on a web page. When the place with the link is clicked, the page selection jumps to the relevant link. An identifying number used to distinguish network devices. The mechanism for restricting network devices that can connect to an access point. Unless the device has registered its MAC address with the access point, it cannot connect to the access point. A device which connects and allows data transfer between a conventional telephone line and a computer. It converts the digital signals from the computer to analog audio for sending over the phone line, and vice versa. A communications business that offers Internet connection services. In order to connect to the Internet, it is necessary to contract to a provider. [. . . ] Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * Neither the name of XySSL nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. [. . . ]