User manual YAMAHA PSS-130

[. . . ] Network Setup") . . . . . . . . . . 16 IP Address Mode setting ("6. Network Setup" "IP Address Mode") . . . . . Network Setup" "IP Address") . . . . . . . . . . . . . . . Network Setup" "MAC Address") . . . . . . . . . . [. . . ] If you select "ALL, " the correspondingly-numbered scene will be recalled for all amplifiers. Preset scene A user scene that is protected A user scene that is not protected Scene No. NOTE 00­49 Selects the scene number to be recalled. · If you select "ALL" as the Amp ID, the scene name will not be displayed. · If you select "ALL" as the Amp ID, amplifiers for which there is no correspondingly-numbered scene data will not recall a scene; they will retain their previous state. · Scene number 00 is for returning the amplifiers to their default settings. · If characters not supported by the PSS-130 were used for the scene name in Amp Editor, the corresponding locations will be shown as "~. " For details on the characters supported by the PSS-130, refer to "List of supported characters" (page 21) at the end of this manual. · Scene names that can be displayed by the PSS-130 are a maximum of 12 characters. If a scene name of 13 characters or longer is specified in Amp Editor, the PSS-130 will not display the thirteenth and subsequent character. · If you edit a parameter after recalling a scene, the E symbol (edit symbol) will be shown in screens that show the scene number. Storing a scene ("1. Scene" "Store") Stores a scene for the specified amplifier. Amp ID: 01 å 01:Scene Name Explanation Parameter Amp ID Attributes of the scene Range 00­39, ALL Selects the ID of the amplifier for which to store a scene. If you select "ALL, " the current scene will be stored to the selected scene number of all amplifiers. Preset scene A user scene that is protected A user scene that is not protected Scene No. The selectable range is 0 dB through -44 dB in 1 dB steps, -44 dB through -78 dB in 2 dB steps, with -78 dB followed by -. Amp Ch: A -48. 0dB å PSS-130 Reference Manual 11 Panel operations Amplifier output monitor ("3. Output Monitor") This indicates the output level of the amp connected to the PSS-130. 3 å. Output Monitor Amplifier output ("3. Output Monitor") Displays the output level for each channel of the specified amplifier. Amp ID: A~B~ Explanation 01 å Parameter Amp ID Level 00­39 0 1 2 3 4 5 6 7 Range Selects the ID of the amp whose output level you want to view. Nothing will appear in the meter if the level is below 0 dBu. 0­6 dBu 6­16 dBu 16­22 dBu 22­28 dBu 28­34 dBu 34­41 dBu 41 dBu­ Device setup ("4. Device Setup") Here you can make settings to identify the PSS-130 connected to the network and the amplifiers connected to the PSS-130. 4 å. Device Setup Device ID Device ID setting ("4. Device Setup" "Device ID") Specifies the PSS-130's Device ID. Set the Device ID so that it does not conflict with another PSS-130 etc. connected to the network. Device ID 001 å Explanation Parameter Device ID NOTE Range 000­255 Selects the PSS-130's Device ID. · If you press and hold down this button for three seconds or longer while the HOME screen is displayed, the screen will appear. View PSS-130 name ("4. Device Setup" "Device Label") Displays the name of the PSS-130 assigned by Amp Editor. NOTE · This shows up to 14 alphanumeric characters. The fifteenth and following characters will not be shown. [. . . ] Never turn off the power while this message is shown. Never turn off the power while this message is shown. Never turn off the power while this message is shown. If this does not solve the problem, contact your Yamaha dealer. [. . . ]