User manual YAMAHA PSS-26

[. . . ] Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. [. . . ] Note · The settings in the FADE TIME screen are independent for each scene. If you edit these settings, you must store that scene in order to make your changes effective. · The Fade function will apply when you recall a scene for which the ENABLED button is selected. B INPUT CH PANNING ENABLED/DISABLED (Input channel panning enable/disable) If the ENABLED button is selected, the Fade function will also apply to the PAN (BALANCE) parameter of input channels. This button is independent from the FADING ENABLED/DISABLED (1) setting. Use the following two buttons to select the input channels to which this will apply. · When the ALL INPUT button is on The Fade function will apply to the PAN (BALANCE) parameter of all input channels. · When the SAME AS FADING button is on The Fade function will apply to the PAN (BALANCE) parameter of only the input channels you select in 4. C FADE TIME/START OFFSET Use the following two buttons to select the parameters that can be viewed/edited in the FADE TIME screen. The indication at the right shows which button is currently selected. · When the FADE TIME button is on Edit the time (fade time) over which the fader or pan parameter of the corresponding channel will reach the new value when you recall a scene for which the Fade function is enabled. 184 PM5D/PSS-26 V2 / DSP5D Owner's Manual Reference section F CLEAR ALL This button disables the Fade function for all input channels or output channels. 4 D Channel settings 56 In this window, select the copy-destination item and click the OK button; the value of the selected channel will be copied. PM5D/PSS-26 V2 / DSP5D Owner's Manual Reference section 185 Appendices Input functions Here you can turn the Fade function on/off and specify the fade time (or the start offset time) for each input channel / output channel. Use the channel name buttons to switch the Fade function on/off. The box below each button lets you specify the fade time or start offset time. You can select the following parameters. MIDI REMOTE function 3 4 MIDI REMOTE function Note The various MIDI REMOTE function screens other than the DME CONTROL screen are invalid if the DSP5D is selected. MIDI SETUP screen Here you can select the types of MIDI message transmitted and received by the PM5D, and select the MIDI port that will be used. MIDI SETUP C DESTINATION SCENE (Paste-destination scene) This list lets you select the scenes to which the data will be pasted. If you want to select multiple consecutive scenes as the paste-destination, select the starting number in the upper list and the ending number in the lower list. (If you're pasting to only one scene, select the same scene in the upper and lower lists. ) You can change the order in which the list is sorted by clicking the buttons shown at the top of the scene number, SCENE TITLE, TIME STAMP, or COMMENT columns. 1 2 3 4 D PASTE This button executes the Global Paste operation. When you click this button, a confirmation message will appear. In the case of parameters such as those listed below, of which only one exists for each two adjacent odd-numbered/even-numbered channels or modules, the parameter will be pasted only if both channels/modules are specified for pasting. · GATE STEREO LINK · COMP STEREO LINK · DELAY GANG · PAN MODE · GEQ LINK · ATT GANG · MS DECODE · FIXED/VARI Note · Paste is valid even in PREVIEW mode. · When you paste to a scene, there may be cases in which a conflict in pairing settings causes the settings of a parameter to differ between L and R channels. In such cases, the parameter will be recalled with those settings, and will be linked when it is next operated. A MODE Here you can select the way in which program changes and control changes will be transmitted/received. · PROGRAM CHANGE MODE In this area you can select the program change transmission/reception method. SINGLE If this button is on, program changes will be transmitted/received on a single MIDI channel (Single mode). OMNI ON/OFF If this button is on, program changes of all MIDI channels will be received in Single mode (this is unavailable in Multi mode). 188 PM5D/PSS-26 V2 / DSP5D Owner's Manual Reference section BANK ON/OFF If this button is on, bank select messages will be transmitted and received in Single mode (this is unavailable in Multi mode). [. . . ] Output [+24dBu] +30 +24 +20 +10 +4 0 -10 -20 -30 Nominal [+10dBu] Input OUT OUT OUT OUT OUT OUT OUT Nominal Output [+4dBu] default setting OMNI OUT1-24 Max. Input [-42dBu] CASCADE IN*1 CASCADE OUT*1 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 Max. DSP Noise Floor *1 CASCADE TYPE = PM5D - PM5D, PM5D - DSP5D *2 CASCADE TYPE = PM5D - DCU5D --- DCU5D - PM5D, PM5D - DCU5D --- DSP5D, PM5D - DSP5D - DSP5D, PM5D - DCU5D --- DSP5D - DSP5D, PM5D - DCU5D --- DSP5D - DCU5D --- DSP5D INPUT 1-48 (GAIN MIN. ) ST IN (GAIN MIN. ) INPUT 1-48 (GAIN MAX. ) ST IN (GAIN MAX. ) Nominal [-62dBu] Input -170 -180 -190 [0dBu = 0. 775Vrms] [0dBFS = Full Scale] For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]