User manual YAMAHA PSS-280
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual YAMAHA PSS-280. We hope that this YAMAHA PSS-280 user guide will be useful to you.
Lastmanuals help download the user guide YAMAHA PSS-280.
Manual abstract: user guide YAMAHA PSS-280
Detailed instructions for use are in the User's Guide.
[. . . ] · The PEQ "Q" parameter value goes up to 16.
1
EN
Support for AuviTran Network ASIO Streamer
By connecting the PSS-280-48ES's [3rd] port to a computer (in which the AuviTran Network ASIO Streamer Driver has been installed) via a LAN cable, direct recording or conduct a sound check using the playback from your DAW software (hereinafter called "sound check" in this document). By performing direct recording first, you will be able to conduct a sound check or simulate a rehearsal using that sound source. Choose FROM STAGE BOX mode for direct recording, or choose FROM DAW mode to conduct a sound check. In order to send and receive audio signals to and from a computer, the firmware must be updated to the following versions. [. . . ] · PSS-280-48ES console: V3. 5 or later · EtherSound module: 0C18 or later For the latest information on EtherSound modules and the AuviTran Network ASIO Streamer, refer to the AuviTran Corporation's website. http://www. auvitran. com/ The following software must also be installed in the computer. · AuviTran Network ASIO Streamer: V1. 2. 5 or later · ASIO-compatible DAW software
NOTE
Direct recording
To record directly into a computer, change the PSS-28048ES's settings as follows.
1 Press the SETUP button to access the SETUP
screen.
2 Press the ASIO STREAMER button and the
FROM STAGE BOX button, making them light.
3 Press the SETUP button to close the SETUP
screen. With these settings, the computer will receive the audio signals that are being input to the PSS-280-48ES's ES IN 148 and the audio signals that are being output from the PSS-280-48ES's ES OUT 116. The PSS-280-48ES will receive the audio signals from the STAGE BOX into ES IN 148.
FROM STAGE BOX
Computer (DAW) STAGE BOX IN 148 IN 4964 OUT 148
· For details about settings on your computer and how to use the software, refer to the AuviTran Network ASIO Streamer user's manual and to the user's manual of your DAW software. · If you choose FROM DAW mode, the time display area in the function access area will alternate between showing the time and [FROM DAW]. · The patching within the EtherSound module is changed automatically by the AuviTran Network ASIO Streamer, but the patching of the PSS-280-48ES will not change. · ES OUT 124 are always transmitted to STAGE BOX.
EtherSound connector FROM STAGE BOX FROM DAW ES IN 148 ES OUT 116
[3rd] port
INPUT PATCH
OUTPUT PATCH
PSS-280-48ES
2
Sound check
To conduct a sound check using audio that was previously recorded on a computer, change the PSS-280-48ES's settings as follows.
NOTE
· Some audio signal delay will occur in FROM DAW mode, since the audio signals pass through the computer. When you've finished the sound check, switch to FROM STAGE BOX mode, or press the ASIO STREAMER button to turn it off (unlit).
1 Press the SETUP button to access the SETUP
screen.
2 Press the ASIO STREAMER button and the
FROM DAW button, making them light.
3 Press the SETUP button to close the SETUP
screen. · In ALTERNATE mode, "ALT" will be displayed as the user name in the function access area.
In ALTERNATE mode, the following encoders will change their operation as described. · [HA] encoder Turn the encoder to adjust the attenuation value. If [ATT] is selected for HA KNOB FUNCTION in the PREFERENCE page of the USER SETUP popup window, the encoder will adjust the head amp gain. q COMM PORT This specifies whether the external head amp connected via the PSS-280-48ES's slot will be remotely controlled. To enable remote control, press the [SLOT 1] button to make it light. If you do not wish to use remote control, press the [NONE] button to make it light.
NOTE
· [MIX/MATRIX] encoder Turn the encoder to switch the corresponding send between PRE /POST. Press the encoder to switch the corresponding send on/ off. · [HPF] encoder Press the encoder to switch the high-pass filter on/off. · [DYNAMICS 1] encoder Press the encoder to switch DYNAMICS 1 on/off. [. . . ] · [DYNAMICS 1] encoder Press the encoder to switch DYNAMICS 1 on/off. · [DYNAMICS 2] encoder Press the encoder to switch DYNAMICS 2 on/off.
NOTE
· Remote control is not possible if the port that transmits or receives MIDI messages is specified as SLOT 1. To allow remote control, assign the MIDI port to other than SLOT 1. · For details on operation, refer to "Remotely controlling an external head amp" in the PSS-280 V3 owner's manual.
· In ALTERNATE mode, encoder functions in the SELECTED CHANNEL section other than those listed above are disabled.
6
Improved EQ operation
If you have selected a LOW band or HIGH band whose type can be switched, you can switch the type by turning the EQ[Q] encoder while pressing it when the Q is set to the maximum or minimum value. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA PSS-280
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA PSS-280 will begin.
