User manual YAMAHA PSS-590

[. . . ] RESTRICTIONS · You may not engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE by any method whatsoever. · You may not reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the SOFTWARE. · You may not electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other computers. · You may not use the SOFTWARE to distribute illegal data or data that violates public policy. [. . . ] · Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE. · Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD PARTY SOFTWARE. 7. GENERAL This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect. 8. COMPLETE AGREEMENT This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha. Special Notices · The software and this manual are the exclusive copyrights of Yamaha Corporation. · Please read carefully the Software Licensing Agreement at the front of this manual before installing the application. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. · Future upgrades of application and system software and any changes in specifications and functions will be announced at the following website. When a device is selected in the list it's IP address also appears in the Device IP Address field in the device information area (2) below the list. Device MAC Address The MAC address of the corresponding device. When a device is selected in the list it's MAC address also appears in the Device MAC Address field in the device information area (2) below the list. Device Port No. The MIDI port number of the corresponding device. When a device is selected in the list it's MIDI port number also appears in the Device Port No. field in the device information area (2) below the list. [New] Button Click this button to add a new device to the list. Edit the device's parameters as required via the fields in the device information area (2) below the list, then click the [Apply] button to add the specified device. [Duplicate] Button This button adds a device to the list by copying the data from the currently selected device. Edit the new device's parameters as required via the fields in the device information area (2) below the list, then click the [Apply] button to add the specified device. [Remove] Button Deletes the selected device from the list. The MIDI port number also functions as device ID number. It should be set to "1" for LS9. n The MIDI port number must be set properly or communication with the device will not be possible. [Apply] Button Click the [Apply] button after editing the Device Name, Device IP Address, Device MAC Address, or Device Port No. parameters to actually apply the changes. Also, devices added to the Target Device List (1) by pressing the [NEW] or [DUPLICATE] buttons will only actually be registered for communication with the DME-N Network Driver when the [Apply] button is pressed. 3 [Advanced Settings] Button Opens the "Advanced Settings" dialog box. This window provides access to advanced settings. [. . . ] Enter your computer's IP address into [IP address], the Gateway's IP address into [Default gateway], and "255. 255. 255. 0" into [Subnet mask]. n When installing on the same subnet as the DME unit(s), set the gateway's host address to 254. DME-N Network Driver Installation Guide for LS9 11 Troubleshooting (FAQ) When controlling the LS9 from your computer via Ethernet, the LS9 does not operate correctly. · Is the Ethernet cable connected correctly? Refer to the "Connection of computer and the LS9" section. · Is the DME-N Network Driver set up appropriately? Refer to the "Setup" section. · Did you enter an appropriate IP address of the LS9? Set the IP address of the LS9 in the MISC SETUP screen of the LS9. If you are connecting the LS9 to your computer in a one-to-one connection, we recommend that you make the following initial settings. IP address Gateway address Subnet mask 192. 168. 0. 128 192. 168. 0. 1 255. 255. 255. 0 However, it must not conflict with the IP address of any other device on the network. For details on settings when connecting to a LAN, refer to the LS9 Editor installation guide. · Is the computer network setup appropriately? Confirm the network setup by following the procedures in the "TCP/IP Settings" section. [. . . ]