User manual YAMAHA PSS480E

[. . . ] IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. [. . . ] · Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a fire and electrical shock hazard. In particular, be careful not to place heavy objects on a power cord covered by a carpet. · Be sure to ground the unit to avoid the risk of electrical shock · If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet. Using the unit in this condition is a fire and electrical shock hazard. · Should this unit/AC adapter/power supply be dropped or the cabinet be damaged, turn the power switch off, remove the power plug from the AC outlet, and contact your dealer. If you continue using the unit without heeding this instruction, fire or electrical shock may result. · If the power cord is damaged (i. e. , cut or a bare wire is exposed), ask your dealer for a replacement. Using the unit with a damaged power cord is a fire and electrical shock hazard. · Do not remove the unit's cover. · Be sure to ground the unit before you insert the power plug into an AC outlet. · If the power cord has three pins and the ground connector on the AC outlet is grounded, the unit will be grounded effectively. Operating Notes · The power must be turned on/off using the POWER switch of this unit. Do not turn the power on/off by plugging in the power cable, or by using a power strip or circuit breaker. · Do not rapidly turn on and off the POWER switch of this unit. Doing so may cause excessive current to damage the system. You must allow at least five seconds to elapse between power-on and power-off. · For this unit, be sure to use a power voltage of the value specified in the Specifications section of this Owner's Manual. If you apply a higher or lower voltage, a malfunction may result. Rack Mounting Caution If the unit is rack mounted and transported regularly, for example, when on a tour, we recommend that the rear of the unit be supported by fitting a pair metal brackets, one each side. The following drawing provides the information necessary to make such brackets. Note that only one bracket is shown here and the bracket for the other side must be bent in the opposite direction. 2-R2 2-R2 (82. 1) 76. 2 31. 75 R5 3. 1 20. 5 200 0 5. 9 4- ø 6. 5 36. 5 14. 5 0 7. 5 t = 1. 6 134 0 8 12 R2 3 86. 5 44. 45 Thank you for choosing the DSP unit "DSP1D/PSS480E", specifically designed for the Yamaha PM1D digital audio mixing system. The DSP1D/PSS480E is an engine controlled by the CS1D control surface. [. . . ] Grounding the unit is also effective for preventing hum and other noise. N OUTPUT 1­6 slot Use these slots to connect the INPUT connectors of an analog output unit AO8 series or DIO8 digital I/O unit to output multi-channel digital audio signals from the DSP1D/PSS480E. Use a genuine Yamaha half-pitch 68-pin cable for connection. Specifications Sampling frequency <External sync> 39. 69 kHz ­ 50. 88 kHz <Internal sync> 44. 1 kHz, 48 kHz USA and Canada : 120 V, 60 Hz Others : 230 V, 50 Hz 170 W 480 mm × 408. 7 mm × 460. 8 mm 33 kg 10 ­ 35°C always fixed power cable 2. 5 m × 1 Power supply Power consumption Dimensions (W × H × D) Weight Operating temperature Fan circuit Accessories Digital I/Os I/O connectors DIGITAL I/O INPUT 1 ­10 DIGITAL I/O OUTPUT 1 ­ 6 DIGITAL I/O CASCADE IN, OUT DIGITAL I/O CONSOLE I/O 1, 2 CONTROL I/O CONSOLE 1 IN, OUT CONTROL I/O CONSOLE 2 IN, OUT REMOTE RS-422 GPI TIME CODE IN MIDI IN, OUT, THRU PC CONTROL RS-232-C PC CONTROL USB WORD CLOCK IN WORD CLOCK OUT RS-422 RS-422 RS-422 RS-422 ­0. 225V -- ­1. 825V/50 ­0. 225V -- ­1. 825V/50 RS-422 C-MOS IN, Open collector OUT 1 pin: 150mA, 8pin total: 500mA SMPTE format, Nominal ­10 dB/10 k MIDI format RS-232-C 0V -- 3. 3V TTL/75 (ON/OFF) TTL/75 Level Type D-sub, half-pitch, 68-pin connector (female) × 10 D-sub, half-pitch, 68-pin connector (female) × 6 D-sub, half-pitch, 68-pin connector (female) × 2 D-sub, half-pitch, 68-pin connector (female) × 2 BNC connector × 2 BNC connector × 2 D-sub, 9-pin connector (female) D-sub, 25-pin connector (female) XLR-3-31 type connector 5-pin DIN connector × 3 D-sub, 9-pin connector (male) B type USB connector BNC connector BNC connector 6 Slots (for IDB1D board) Unit DPS1D DPS1D-EX Input channel INPUT 1-48 & ST IN 1-4* INPUT 1-96 & ST IN 1-8 (DSP1D + IDB1D for expansion) *The DSP1D has an empty slot available for the IDB1D board. Dimensions 460. 8 408. 7 480 ENGINE ID A B CONTROL I/O 1 2 INPUT CONFIGURATION 48CH 96CH POWER ON/ OFF 399. 2 450 · Specifications and appearance are subject to change without notice for improvement. · For European Model Purchaser/User information specified in EN55103-1 and EN55103-2. Inrush Current: 31A Conformed Environment: E1, E2, E3 and E4. 9. 5 unit: mm 7 For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. [. . . ]