User manual YAMAHA QY100E1

[. . . ] Owner's Manual SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over , or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! [. . . ] "16" for the sequencer tracks, the accompaniment "Pt" track, the accompaniment "Cd" track, the "Tm" track, or "Al" (All) tracks. When "Pt", "Cd", Tm" or "Al" is selected, the lower "TR" parameter is automatically set to the same track. The lower "TR" parameter selects the destination track -- i. e. the track to which the data is to be copied: "01" . . . "16" for the sequencer tracks, the accompaniment "Pt" track, the accompaniment "Cd" track, the "Tm" track, or "Al" (All) tracks. When "Pt", "Cd", Tm" or "Al" is selected, the upper "TR" parameter is automatically set to the same track. The "M" parameters above the upper graphic bar are used to specify the first measure:beat and last measure:beat of the range to be copied. First measure Last measure First beat Last beat 162 The Song Jobs The "M" parameters below the lower graphic bar specifiy the destination measure:beat to which the data will be copied, as well as the number of times the data is to be copied. Destination measure Number of times to be copied Destination beat ;; ;; The "Transpose" parameter sets a transpose value for the copied data in semitone increments from "-24" through "+00" to "+24". The Chord template parameter, above the upper graphic bar, appears only when the "Cd" track is selected at the "TR" parameter. This parameter specifies which chord progression, either the user chord progression programmed in the source "Cd" track or preset chord template, will be copied to the User chord progression. After setting the parameters as required press [ENTER] to execute the Copy Event job. The metronome icon will appear on the display while the data is being processed, then "Completed !" will appear briefly when the job is done. Press the [EXIT] button to return to the job list, or a mode button to go directly to the selected mode. NOTE · Previous data in measures overwritten by the Copy Event job will be completely erased and replaced by the copied data. · · The time signature is copied by the Copy Event job, but Voice and Play Effect data is not copied. The Copy Event job makes it easy to use phrases or even complete sections (an entire chorus, for example) in more than one place in a song. You can copy a phrase played by one voice, and have it repeated by a different voice later in the song. You can always edit the copied sections to create variations. Since the default copy source range is M001 . . . 999 (measures), an "Illegal Input" error will occur if you attempt to copy to measure 002 or later without first changing the source range. Be sure to set an appropriate source range even when the chord track ("Cd") is selected as source track. 163 · The Song Jobs 10 : Erase Event Erases all note and event data from the specified measure or range of measures in the specified track. An erase operation leaves the specified measures intact but blank. First measure Last measure First beat Last beat The "TR" parameter selects the track to be affected by the Erase Event job: "01" . . . "16" for the sequencer tracks, the accompaniment "Pt" track, the accompaniment "Cd" track, or the "Tm" track. The "M" parameters above the graphic bar are used to specify the first measure:beat and last measure:beat of the range to be erased. [. . . ] Nusantik Gedung Yamaha Music Center, Jalan Jend. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 CENTRAL & SOUTH AMERICA MEXICO Yamaha de Mexico S. A. De C. V. , Departamento de ventas Javier Rojo Gomez No. 1149, Col. Tel: 55-5804-0600 SPAIN/PORTUGAL Yamaha-Hazen Música, S. A. [. . . ]