User manual YAMAHA R70

[. . . ] IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. [. . . ] Press again to select the top of subsequent indexes. The number of the selected index is displayed by the index counter. If the specified index cannot be found, the first index is selected. CDR1000--Owner's Manual 24 Chapter 4--Playback Searching You can search the program material at high speed using the SEARCH [ buttons during playback or playback pause. 1 ] and [ ] Press and hold the backward SEARCH [ ] button to search backwards. The CDR1000 searches backwards from the current position and the PLAY indicators go out. If the top of the current track is reached, searching continues into the previous track. If the top of the first track is reached, searching stops. When the SEARCH [ ] button is released, the previous mode--playback or playback pause--is resumed and the relevant indicators light up. 2 Press and hold the forward SEARCH [ ] button to search forwards. The CDR1000 searches forwards from the current position and the PLAY indicators go out. If the end of the current track is reached, searching continues into the next track. If the end of the last track is reached, searching stops. While searching is in progress, playback signals are output by the ANALOG OUT and PHONES only, the AES/EBU OUT and COAXIAL OUT are muted. Using Repeat Playback The CDR1000 provides three types of repeat playback: One-track Repeat, in which the current track plays repeatedly, All-track Repeat, which plays all tracks repeatedly, and A-B Repeat, which repeatedly plays the region between the specified A and B points. One-track Repeat Playback 1 Press the [REPEAT] button. One-track Repeat playback starts and "REPEAT 1" appears on the display. Press the [REPEAT] button twice to cancel One-track Repeat playback. Recording via the AES/EBU IN or COAXIAL IN is not possible while the LOCK indicator is flashing. CDR1000--Owner's Manual 26 Chapter 5--Recording Setting the Sampling Rate Converter The CDR1000 features a built-in sampling rate converter (SRC), which means digital sources at sampling rates other than 44. 1 kHz, the standard for audio CDs, can be recorded. The SRC can convert digital audio within the range 30­50 kHz. When recording from a 44. 1 kHz digital source, the CDR1000 locks to the sampling rate of the incoming signal. If the signal drifts by more than ±150 ppm (parts per million), the CDR1000 automatically activates the sampling rate converter. The Utility SRC parameter is used to set the sampling rate converter. 1 Use the [UTILITY] button to select "SRC. " The UTILITY indicator lights up and the SRC setting appears on the display. Use the [PREV] or [NEXT] button to set the sampling rate converter to either "ON" or "AUTO. " Setting AUTO ON Description The sampling rate converter is off unless the 44. 1 kHz sampling rate of the selected digital input source varies by more than ±150 ppm, in which case it is activated automatically. The sampling rate converter is always on. 2 3 Press and hold the [UTILITY] button, or press another button to cancel Utility. The SRC indicator lights up when the sampling rate converter is active, that is, when it's set to ON, or when it's set to AUTO and activated automatically. The Utility SRC parameter should be set to ON when recording non-44. 1 kHz digital sources, and set it to AUTO when recording 44. 1 kHz digital sources. The SRC does not affect analog sources connected via the ANALOG IN. Note: When the sampling rate of the incoming signal nears the 150 ppm drift threshold, the SRC indicator may flash, in which case you should set the SRC parameter to ON. CDR1000--Owner's Manual Setting the Input Delay 27 Setting the Input Delay By storing incoming audio in a buffer of between 0 and 4, 950 ms before recording it to disc, the Input Delay function offers a "pre-record" facility, which can record a small section of audio before the point at which recording is started. [. . . ] Make sure that the DAT Start IDs are positioned slightly before the start of each track. See "Sync Recording from CD, MD, or DAT" on page 39 for more information. If no input signal is received for 20 or more seconds, Sync Recording stops automatically. See "Sync Recording from CD, MD, or DAT" on page 39 for more information. CDR1000--Owner's Manual 54 Appendix Appendix Error Messages If the CDR1000 displays an error message, follow the instructions below. Error Number 0XXXXX 1XXXXX 2XXXXX 3XXXXX 4XXXXX 5XXXXX 1. [. . . ]