User manual YAMAHA RAV120

[. . . ] On the Yamaha remote control, slide the MEMORY switch to position B. Aim the VCR remote control transmitter (usually located at the top) at the top of the Yamaha remote. Remote With Lid Open VCR Remote Control REC/ PAUSE CLEAR REC PAUSE AB TAPE CD FAST FORWARD TUNER 2. Slide Memory Switch To B VC R T V D BS A DIR B LEARN PRES E T 2~4 " T RANSMI T / L E A RN MA CRO A /B PRO LOGIC ENHANCED CONCERT VIDEO 1 MONO MOVIE 2 S TAD IUM 3 DI SC O V-- AUX VC R TUNER TAPE CD 4 R O CK 5 H A LL 6 PHO N O 7 8 9 TE S T EFF ECT 0 TIME LE V EL DELAY CENTER REAR SWFR 3. On the Yamaha remote, use a paper clip or mechanical pencil to press LEARN. The TRANSMIT/ LEARN red LED will start to flash. NOTE: If there is no operation for about 30 seconds after a button is pressed, the TRANSMIT/LEARN LED will flash repeatedly. [. . . ] Slide MEMORY Switch To B A STOP DIR B D ISC VC R D V D LD Remote With Lid Open TV Remote Control REC PAUSE CLEAR T V D BS VOLUME UP VOLUME DOWN CHANNEL KEYPAD (0~9) A DIR B LEARN 2~4" T RANSMI T LE ARN MA CRO AB CHANNEL UP PRO LOGIC ENHANCED CONCERT VIDEO 1 MONO MOVIE 2 S TAD IUM 3 DI SC O AUX V-- TUNER TAPE VC R CD 4 R O CK 5 H A LL 6 PHO N O 7 8 9 TEST EFF ECT 0 TIME LE V EL TV INPUT DELAY CENTER REAR SWFR 3. CHANNEL DOWN SLEEP On the Yamaha remote, use a paper clip or mechanical pencil to press LEARN. The TRANSMIT/ LEARN red LED will start to flash. NOTE: If there is no operation for about 30 seconds after a button is pressed, the TRANSMIT/LEARN LED will flash repeatedly. If this occurs, restart from step 3. 2CH/6CH SY S T E M P O W ER TV MAS T ER VO LUM E TV POWER 4. OFF VCR On the Yamaha remote, press and release the button to which you want to assign the function. On the TV remote, press and release the button for the corresponding function. After one second, the TRANSMIT/LEARN LED will flash slowly. The TRANSMIT/LEARN red LED on the Yamaha remote control will flash slowly after the function is learned. NOTE: If the TRANSMIT/LEARN red LED on the Yamaha remote flashes rapidly, the function has not been learned. Repeat steps 5 and 6 to program the function. 5. R EMO T E C ONT R O L T R ANSMIT T ER Remote With Lid Open 6. 7. 9. Continue programming until you have learned functions into all of the shaded buttons. To test programming, press TV (power) to turn on the TV. Then press each button you've programmed. Repeat steps 1 through 8 for any function that does not respond. Remote Control Guide · BASIC OPERATION CONTROLS TRANSMI T USING FACTORY-PRESET OPERATIONS In addition to the programmable VCR and TV functions, the Yamaha remote control will also perform several factory-preset operations without additional programming (see the illustration on the left): 1. Close the lid of the Yamaha remote control. Slide the Macro switch (on the side) to QUICK. Press the SYSTEM POWER button to power up your Yamaha receiver, VCR, and TV. NOTE: Since power ON and OFF are controlled by the same button on most audio and video components, the (SYSTEM POWER) OFF button may not turn off your VCR and TV automatically (see "Creating A Macro" on the next page). Press the VCR button to set the input on the receiver to VCR and put the VCR into PLAY mode. (Make sure there is a videocassette in the machine. ) NOTE: You may have to adjust the INPUT on your TV to see the VCR's video signal. If you have programmed the TV inputs into the Yamaha remote's TEST button, simply press it (one or more times) until you see tape playback. [. . . ] Open the lid of the Yamaha remote control. Use a paper clip or mechanical pencil to press the MACRO selector. Press the OFF button to clear the original factory macro and assign the new sequence of functions (i. e. , steps 5, 6, and 7) to this button. Press the VCR button Press the OFF button. [. . . ]