User manual YAMAHA RIO1608-D

[. . . ] Owner's Manual Keep This Manual For Future Reference. EN Contents PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Firmware Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Precautions for Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Recessed Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Accessories (Please check the package contents. ) · Owner's Manual · AC power cable · Dante Virtual Soundcard license code About Dante . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Controls and Functions. . . . . . . . . . . . . . . . . . . . [. . . ] Use the rotary switch while the power to the unit is turned OFF. Otherwise, the ID setting will not be effective. Owner's Manual 9 Controls and Functions 6 DIP Switches These switches enable you to specify the settings related to the startup operation of the unit. Set the DIP switches while the power to the unit is turned OFF. Otherwise, the setting will not be effective. · Switch 1 (UNIT ID) This switch setting determines whether the hexadecimal setting of the [UNIT ID] rotary switch will range from 0 to F or from 10 to 1F. Switch Setting UNIT ID ranging from 0 to F UNIT ID ranging from 10 to 1F Description The setting range of the [UNIT ID] rotary switch is from 0 to F. The setting range of the [UNIT ID] rotary switch is from 10 to 1F. · Switches 5 and 6 (REMOTE) When you plan to monitor or control the Rio from a digital mixing console, these switches determine whether to use an Rio-native device (such as a CL series product) or a non-Rio-native device. Information on which devices feature Rio-native support is available at the Yamaha pro audio website product page: http://www. yamahaproaudio. com/products/ Switch Setting NATIVE Description An Rio-native device will control the Rio. 56 AD8HR 1 1 56 · Switch 4 (SECONDARY PORT) This switch setting determines whether the rear-panel [SECONDARY] connector will be used for a daisy chain or redundant network. With the [DAISY CHAIN] setting, you can connect multiple Dante-enabled network devices in a daisy chain without using a network switch. Refer to "Daisy Chain Network" in the "About Connections" section (see page 13) for more information about daisy chain connections. With the [REDUNDANT] setting, the [PRIMARY] connector will be used for primary connections, and the [SECONDARY] connector will be used for secondary (backup) connections. If the unit is unable to transmit signals through the [PRIMARY] connector for some reason (e. g. , due to damage or accidental removal of the cable, or a failed network switch), the [SECONDARY] connector will automatically take over communications and functions on the redundant network. Refer to "About Redundant Networks" in the "About Connections" section (see page 13) for more information on redundant networks. Switch Setting DAISY CHAIN Description The [SECONDARY] connector is used for a daisy chain connection. A signal at the [PRIMARY] connector will be transmitted to the next device in the chain as is. The [SECONDARY] connector is used for a redundant network. It will function as backup connection, independent of the network to which the [PRIMARY] connector is connected. A non-Rio-native device will control the Rio as AD8HRs. In this case, Rio3224-D and Rio1608-D are recognized as four AD8HRs and two AD8HRs respectively. The unit with any other UNIT ID numbers will not be controllable. · Switches 7 and 8 (START UP MODE) These switches determine whether part of the internal memory is initialized when the unit starts up, or uses the previous settings (i. e. , settings used prior to the most recent power-off). If you plan to connect an Rio-native device, such as a CL series product, set the switches to [REFRESH]. The Rio will not input or output audio until the connected Rio-native device transmits its settings to the Rio, so that the Rio will not output audio accidentally. Switch Setting REFRESH Description The Rio starts up with part of the internal memory initialized. HA GAIN +48V HPF HPF Gain Compensation Dante Patch RESUME ­6 dB OFF OFF 80Hz OFF OFF 78 4 78 The unit starts up using the settings assigned prior to the most recent power-off. REDUNDANT 4 10 Owner's Manual Controls and Functions 7 [SYSTEM] Indicators These indicators show the Rio's operating status. If the green indicator lights steadily and the red indicator turns off, the unit is operating normally. When power to the unit is turned ON, if the green indicator turns off, or if the red indicator lights or flashes, the unit is not functioning properly. [. . . ] Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 MALTA Olimpus Music Ltd. Louis Street Msida MSD06 Tel: 02133-2144 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]