User manual YAMAHA RS70/85 ASSEMBLY MANUAL

[. . . ] · To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Do not use benzine, thinner or alcohol as it may result in discoloration or deformation. [. . . ] Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product, it may result in deterioration. PRECAUTIONS Before using, please read this "Assembly Instruction" sheet, and use this product in a safe and proper manner. Especially for children, parents or an instructor should teach the children the proper manner in which to use the device. Inside This Package Before setup, please make sure that all of the items listed below are present and accounted for. If anything is missing, please contact the dealer from whom you purchased the unit. Overall Assembly RS70/85/85 (When the box is opened) To prevent against accidents and injury Please follow the cautions listed below Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to. Acts indicated with this icon are prohibited and should not be attempted. WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Small Screws M5 X 8 (Module Holder Fixing Screws X4) Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the instrument being unstable and overturning. Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury. A Phillips (+) screwdriver is required when attaching the Drum Trigger Module module. Please prepare one before starting assembly. 1 2 After removing the unit from the box, remove all cushion material. Setting up the parts · Loosen the bolts on the movable arms and legs, as shown in the diagrams below, then secure the bolts firmly once setting is complete. Follow the setup order (q~u) in the diagrams shown below. Caution : Make sure the bolts marked with a " " are loosened before setting up. 3 Attaching the Drum Trigger Module 3-1 Remove the module holder from the holder clamp, and use the supplied screws to attach the Drum Trigger Module. Make sure only the supplied screws are used. Using any other screws may result in the unit falling off the holder or damage. 3-2 Reattach the module holder to the holder clamp. Cymbal Holder Module Holder Assembly r t e u Caution Caution y Side Arm (R) Assembly Side Arm (L) Assembly q w Right Leg Assembly Left Leg Assembly Optional Parts Pad and Drum Trigger Grouping q DTX Series Drum Trigger Module w TP65/65S Drum Pad e PCY65/65S Cymbal Pad RS70/85/85+ Pad grouping : Set up example PCY65S e Speaker e Speaker r KP65 Kick Pad t HH65 Hi-hat Control Pedal y Foot Pedal FP-7210 etc. q w w Monitor System and Attchement Grouping · SPAT1 Speaker Attchment · TPCL65 Tom Holder · CYAT65 Cymbal Attchment w w TP65S r · MS50DR Monitor System · MS100DR Monitor System Monitor System t y 4 Step 3 Step 4 Attaching the cymbal pads Attach the cymbal pads to the cymbal holders and adjust their position, then secure in place. [. . . ] Using any other screws may result in the unit falling off the holder or damage. 3-2 Reattach the module holder to the holder clamp. Cymbal Holder Module Holder Assembly r t e u Caution Caution y Side Arm (R) Assembly Side Arm (L) Assembly q w Right Leg Assembly Left Leg Assembly Optional Parts Pad and Drum Trigger Grouping q DTX Series Drum Trigger Module w TP65/65S Drum Pad e PCY65/65S Cymbal Pad RS70/85/85+ Pad grouping : Set up example PCY65S e Speaker e Speaker r KP65 Kick Pad t HH65 Hi-hat Control Pedal y Foot Pedal FP-7210 etc. q w w Monitor System and Attchement Grouping · SPAT1 Speaker Attchment · TPCL65 Tom Holder · CYAT65 Cymbal Attchment w w TP65S r · MS50DR Monitor System · MS100DR Monitor System Monitor System t y 4 Step 3 Step 4 Attaching the cymbal pads Attach the cymbal pads to the cymbal holders and adjust their position, then secure in place. (Please refer to the Owner's Manual that came with the cymbal pads on attaching the cymbal pads. ) Drum Trigger Module Module Holder Step 3-1 Step 3-2 Holder Clamp Cymbal Pad 5 Attaching the drum pads Attach drum pads to the hexagonal rod cylinder and adjust their position, the secure in place. Make sure all bolts on clamps, pads, etc. , are firmly tightened. [. . . ]