User manual YAMAHA RS7000V12E

[. . . ] · The note at the cursor location on the STEP RECORD display. · The note at the cursor location on the EDIT display. · The note currently playing in the currently selected track. I Switching Sections via the Keyboard Pads (Owner's Manual page 72) In addition to sections A ~ J, it is now possible to select sections K ~ P via the keyboard pads. [. . . ] G Note Scan This function provides a convenient way to locate a specific instrument in a recorded rhythm track. Press [F1] to move to the nearest recorded note that is higher than the current note. RS7000 1 G Set grid resolution. It is now possible to specify the grid resolution. 4 RESOLUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [DIAL 4] [Settings] Range: 15 (128th-notes), 20 (64th-note triplets), 30 (64th notes), 40 (32nd-note triplets), 60 (32nd notes), 80 (16th-note triplets), 120 (16th notes), 160 (8th-note triplets). When the number of grid units per measure is greater than 16 the keyboard pad edit location with the measure is set via the [OCT DOWN] and [OCT UP] buttons. The keyboard pad LEDS indicate the current edit location while the [OCT DOWN] or [OCT UP] button is held. When a triplet resolution is selected only keyboard pads 1 ~ 12 are used. MUTE KEYBOARD ARPEGGIO ON OCT DOWN OCT UP STORE SCENE 1 2 MEMORY 3 NK SECTION RANSPOSE A B C D E CAPS ALL 1~8 9~16 TR- TR+ TRACK MUTE 1 2 3 4 5 6 7 8 9 SOLO K!L# M$ N% O& P' Q( R) S- TRANSPOSE(-) TRANSP In this example the fourth of a possible eight locations is selected for editing. G Measure Hold The Measure Hold can now be selected from the Grid Step record standby mode (Owner's Manual page 78). 7 MEASURE HOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [DIAL 3] Can be set when the Grid Step record type is selected. [Settings] Range: ON, OFF 1-measure monitoring is selected when ON, full-pattern monitoring when OFF. I Changes to the Voice Edit Filter Page (Owner's Manual page 102) 12 new Voice Edit filter types are provided in addition to a new "Distance" parameter. 1 CUTOFF FREQUENCY (CUTOFF) (Refer to Owner's Manual page 103) 2 DISTANCE (DST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [F1] [DIAL 1] Relative [Settings] Range: ­32 ~ +31 Specifies the distance between the two frequencies for the dual-type filters (Dual LPF, Dual HPF, Dual BPF, Dual BEF) and LPF+BPF combined filter. When set to "0" the two cutoff frequencies are equal. 2 RS7000 3 RESONANCE (Refer to Owner's Manual page 103) 4 FILTER TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [DIAL 3] Absolute [Settings] Range: BYPASS, LPF24D, LPF18, LPF12, HPF24D, BPF12D, BEF12, LPF24A, LPF18s, LPF6, HPF12, BPFw, BPF6, BEF6, Dual LPF, Dual HPF, Dual BPF, Dual BEF, LPF+BPF NOTE Please note that data created using the new filter types added in this firmware update will not work properly on previous versions. Filter Name BYBASS LPF24D (24dB/oct Digital Low Pass Filter) Old Name BYPASS LPF24 Characteristics Direct throughput with no filter effect. [. . . ] Two 12dB/oct low-pass filters connected in parallel. Two 12dB/oct high-pass filters connected in parallel. Two 6dB/oct band-pass filters connected in parallel. [. . . ]