User manual YAMAHA RS95

[. . . ] RS95 A B C D E F G H I J K L M N u o q J G I C J t E F y GI t w D A B GH i !0 !1 !2 q w e r t y u i o !0 !1 !2 H I G 1 A C B 4 H H I I G 2 D I C H G 5 D J C J J M A B 3 E F G F A I E E J G F E I J E G H F A K Electronic Drum Rack System RS95 Assembly Instruction Thank you for purchasing the Yamaha Electronic Drum Rack System RS95. Before using, thoroughly read this assembly manual, and use this product safely and correctly. I RS95 Rack Stand Parts A Left Side Assembly (x1) * Before assembling the rack stand, make sure all of the parts shown below are included. B Right Side Assembly (x1) C Center Pipe Assembly A (x1) D Center Pipe Assembly B (x1) E Module Holder (x1) (4 screws included) F Module Holder Clamp (x1) G Hex Rod Cylinder (x5) H Drum Pad Clamp (Short) (x1) I Drum Pad Clamp (Long) (x3) J Cymbal Holder (x2) K Cable Band (x10) L Tuning Key (x1) M Felt Washer (x2) N Assembly Instruction (this sheet) WARNING Before using, please read this "Assembly Instruction" sheet, and use this product in a safe and proper manner. Especially for children, parents or an instructor should teach the children the proper manner in which to use the device. If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. If this symbol is ignored and the equipment is * Specifications are subject to change without notice. CAUTION used improperly, there is a danger of injury to persons handling the equipment, and material damage could occur. Always set the instrument on a flat and solid surface. [. . . ] They may be pinched resulting in injury. Watch your fingers when adjusting clamps. They may become pinched resulting in injury. Be careful around pipe ends, inside the pipe and screw ends. Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to. Acts indicated with this icon are prohibited and should not be attempted. This icon indicates acts that you are urged to follow. * Specifications are subject to change without notice. I RS95+Pad Grouping: Setup Example u o q J G I C J t E F y GI t w D A B GH i !0 !1 !2 * Please use a snare stand for setting the snare drum pad. G Pad and Drum Trigger Grouping (option) qDTXTREME Drum Trigger Module wRHP120SD Snare Type Real Head Pad (12inch) eRHP120 Real Head Pad (12inch) rRHP100 Real Head Pad (10inch) tRHP80 Real Head Pad (8inch) yTP80S/TP80 Drum Pad uPCY80S/PCY80 Cymbal Pad iKP120 Real Head Kick Pad oPCY10 Trigger Pad !0HH60 Hi-hat Control Pedal !1Foot Pedal *DFP-880 etc. !2Snare Stand *SS-642 etc. * The supplied Drum Pad Clamp H I can be attached to the RS95 and the Hex Rod Cylinder G can be used to attach lighter pads up to TPCL100 the RHP80. Tom Holder When a large, heavy pad, such as the RHP100/ 120 is to be attached, we recommend the use of the tom holder TPCL100 (optional). Includes Holder Clamp Assembly. I RS95 Assembly * A screw driver (+ or -) is necessary to complete the assembly. Please make sure that the fixing bolts on each part, such as clamps, pads, etc. Bolts that are too tight or too loose may result in damage to the part or the part dropping. Please use caution. 1 2 Attach the Center Pipe Assembly A C to the upright pipes of the Left Side Assembly A and the Right Side Assembly B , and tighten the wing bolts. Attach the Center Pipe Assembly B D , and tighten the wing bolts. 4 Attach the Drum Pad Clamps H I 4-1 Insert the Hex Rod Cylinders G into the Drum Pad Clamps H and I , and tighten the fixing screws. 4-2 Attach the Drum Pad Clamp (short) H to the floor tom position. Attach the Drum Pad Clamps (long) I to the high-hat and tomtom positions. [. . . ] 3-4 Attach the Module Holder E , with the DTXTREME attached, to the Module Holder Clamp F . DTXTREME Module Holder E Step 4-3 Step 3-4 Hex Rod Cylinder G Step 3-1 Tighten Step 3-2 Module Holder Clamp F Drum Pad Clamp (Short) H Step 3-3 Step 4-2 Left Side Assembly A After the above assembly is complete, set the Kick Pad, Hi-Hat Control pedal, etc. into position and connect the necessary cables. To keep cable out of the way while playing, use the supplied Cable Bands K to hold the cables to the rack system's pipes. [. . . ]