User manual YAMAHA RX-V1065

[. . . ] U RX-V1065 AV Receiver OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1 2 3 4 5 6 7 8 9 · Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 10 11 12 Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 13 14 Read these instructions. Install in accordance with the manufacturer's instructions. [. . . ] Press jCursor k / n to select "DSP Parameter" and then press jENTER. Sound field program Fine adjusts an effect level (level of the sound field effect to be added). You can adjust the level of the sound field effect while checking sound levels. Adjust "DSP Level" as follows. · There are no differences between effects of the sound field programs. · The sound field effect is added too much. Dialogue Lift Choices: 0* to 5 DSP Parameter Program Name Decode Type DSP Level P. Room Size Sci-Fi PLIIx Movie 0dB 16ms 1. 0 2ms 1. 0 Use this feature to adjust the vertical position of the dialogues in movies. The ideal position of the dialogues is at the center of the video monitor screen. Sound field parameters Set values The ideal dialogue position 5 Press jCursor k / n to select "Program Name" and then press jCursor l / h to select a sound field program to edit. Press jCursor k / n to select a parameter to edit and then press jCursor l / h to change the setting. For details on functions and adjustable ranges of the sound field parameters, see "Sound field parameters" on this page. y · Repeat steps 5 and 6 to change other sound field program parameters. 6 If the dialogues are heard at the lower position of the video monitor screen, increase the value of "Dialogue Lift". Move up to the ideal dialogue position 7 To turn off the GUI screen, press iON SCREEN. When the value is set to zero, the position is at the lowest. The position gets higher as you increase the value. Notes · This setting is available only when "Extra Speaker Assignment" is set to "Presence" (page 56). · You cannot move the dialogue position down from the initial dialogue position. To initialize the parameters of the selected sound field program, press jCursor n repeatedly to select "Initialize" and then press jCursor h. Then, press jCursor h again to execute the initialization or jCursor l to cancel it. 3D DSP Choices: On*, Off When CINEMA DSP 3D is enabled, sets whether to use sound field programs in 3D mode. 50 En Editing surround decoders/sound field programs Note · This setting is available only when "Extra Speaker Assignment" is set to "Presence" (page 56). Level Level Source sound Early Sound field parameters for advanced configurations Parameters for adjusting early-reflected sound INTRODUCTION Time Sound source Time Initial Delay / P. Back Initial Delay Adjustable range: 1 to 99ms (Initial Delay / P. Back Initial Delay) PREPARATION Adjusts attenuation characteristics of early-reflected sound. You can create a lively sound field (with a high reverberant sound level) as you increase the value, and a dead sound field (with a low reverberant sound level) as you decrease the value. Creating either a lively sound field or a dead sound field in an actual music hall is determined by the acoustic absorption characteristics of reflection surfaces. A dead sound field is created when the attenuation time is short while a lively sound field is created when the attenuation time is long. Original source sound Early-reflected sound Small = 0. 1 Large = 2. 0 Parameters for defining attenuation characteristics of early-reflected sound BASIC OPERATION Liveness / P. Back Liveness Adjustable range: 0 to 10 Time Delay Sound source Delay Time Adjusts the attenuation of reflected sound. You can create a lively sound field (with a high reverberant sound level) as you increase the value, and a dead sound field (with a low reverberant sound level) as you decrease the value. [. . . ] 49 Video/audio jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Virtual CINEMA DSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 VOLUME +/-, remote control . . . . . . . . . . . . . . . . . . . . . . . . . 7 VOLUME control, front panel . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]