User manual YAMAHA RX-V2500

[. . . ] GB RX-V2500 AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place -- away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit. [. . . ] Customizes overall audio settings for this unit. Page 58 58 59 59 60 Basic (Basic) Use to quickly setup basic system parameters. Item Test Tone Speaker Set Speaker Distance Speaker Level ADVANCED OPERATION Features Turns the test tone output on or off for Speaker Set, Speaker Distance and Speaker Level settings. Selects the output mode suitable for each speaker, the speakers for low-frequency signal output, and the cross over frequency. Adjusts the output level of each speaker. Page 61 61 64 64 English 53 SYSTEM OPTIONS Option (Option) Use to adjust the optional system settings. Item Display Multi Zone Surr. Initialize Input Mode Memory Guard Adjusts the GUI and front panel displays. Customizes the Zone 2, Zone 3 and Zone B settings. Initializes the parameters of all or a group of sound field programs. Selects the initial input mode of the source. Locks the menu parameter settings. Features Page 65 66 66 67 67 Auto Setup (Auto setup) Use to specify which speaker parameters auto setup will adjust, and to activate the auto setup procedure (see page 26). System Memory (System memory) Use to save and recall various settings (see page 67). Audio Info. (Audio signal information) Use to check audio signal information (see page 39). 54 SYSTEM OPTIONS Changing parameter settings Use the remote control to access and adjust each parameter. AMP 4 Press k / n repeatedly to select the parameter you want to adjust. Presence Bass Out Bass Cross Over SWFR Phase 40Hz 60Hz 80Hz (THX) 90Hz 100Hz + TV VOL + CH + SOURCE VOL ­ TV MUTE ­ A/B/C/D/E ­ MUTE EXIT TV 1 6 3-5 5 TV INPUT 2 TOP TITLE PURE DIRECT MENU NIGHT ENTER AUDIO STRAIGHT RETURN DISPLAY EFFECT 1 2 3 Set AMP/SOURCE/TV to AMP. Press TOP on the remote control. Press ENTER or h, then press k / n repeatedly to change the setting of the item you want to adjust. Presence 40Hz 60Hz 80Hz (THX) 90Hz 100Hz Press k / n repeatedly to select a menu, then press h to enter the selected menu. Bass Out Bass Cross Over SWFR Phase Test Tone Speaker Set Speaker Distance Speaker Level Front Center Surround 6 y Press EXIT. If you want to continue adjusting parameter settings, press ENTER to return to the previously selected menu item. Notes · The available parameters may be displayed on more than one page of the GUI display. · You cannot change parameter values when Memory Guard is set to "Guard". If you want to change the parameter values, set Memory Guard to "Free" (see page 67). Front Center Surround Surround Back Presence Large Small None Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cable is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter values will return to the factory settings. If this happens, edit the parameter value again. ADVANCED OPERATION English 55 SYSTEM OPTIONS Input Select Use this feature to reassign digital input/outputs, select the input signal, rename the inputs, or adjust the level of the signal input to each jack. 1 Set AMP/SOURCE/TV to AMP. AMP SOURCE TV Example 2: To clear a jack assignment. 1) Select Input Select, then select the input source (DVD, etc. ). 2) Select I/O Assignment, then select the jack assignment (Optical Output, Optical Input, Coaxial Input or Component Video). 3) Select NONE, then press ENTER to clear the assignment. I/O Assignment Volume Trim Optical Output Optical Input Coaxial Input 2 3 Press TOP on the remote control. Select Input Select, then press h. CD-R Stereo/Surround Input Select Manual Setup Auto Setup MD/TAPE DVD DTV CBL/SAT Rename y This menu item is also available in the front panel display system options menu (see page 85). Notes · You cannot select a specific item more than once for the same type of jack. · When you connect a component to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack. 4 Select the desired input (CD, DVD, etc. ), then press h to access and adjust. Volume Trim (Volume trim) Use this feature to adjust the level of the signal input to each jack. This is useful if you want to balance the level of each input source to avoid sudden changes in volume when switching between input sources. Input Select > input source (DVD, etc. ) > Volume Trim > Control range: ­6. 0 dB to +6. 0 dB y This menu item is also available in the front panel display system options menu (see page 85). I/O Assignment (Input / output assignment) You can assign the digital audio input/output and component video jacks to other components if this unit's initial settings do not correspond to your needs. Change the following parameters to reassign the jacks and effectively connect more components. Once the jacks are reassigned, you can select the corresponding component using INPUT SELECTOR on the front panel or the input selector buttons on the remote control. [. . . ] and Canada models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 to 1710 kHz [Asia and General models] . . . . . . . . . . . . . . . . . 530/531 to 1710/1611 kHz [Other models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 to 1611 kHz · Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]