User manual YAMAHA RX-V2600

[. . . ] GB RX-V2600 AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place ­ away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit. [. . . ] However, if the power is cut for more than one week, the parameter values will return to the factory settings. If this happens, edit the parameter value again. Front Center Surround Surround Back Presence Large Small None 72 SYSTEM OPTIONS Input Select Use this feature to reassign digital input/outputs, select the input signal, rename the inputs, or adjust the level of the signal input at each jack. Choices: TUNER, PHONO, CD, CD-R, MD/TAPE, DVD, DTV, CBL/SAT, VCR1, DVR/VCR2, V-AUX, MULTI CH Note Some parameters described below may not be available for all input sources and some parameters are only available for specific input sources. Input source TUNER PHONO CD CD-R MD/TAPE DVD DTV CBL/SAT VCR1 DVR/VCR2 Parameter Volume Trim Rename 2 Select Input Select and then press h. CD-R Stereo/Surround Input Select Manual Setup Auto Setup MD/TAPE DVD DTV CBL/SAT 3 Select the desired input source (CD, DVD, etc. ) and then press h to access and adjust. Volume Trim (Volume trimming) You can adjust the level of the signal input at each jack. This is useful if you want to balance the level of each input source to avoid sudden changes in volume when switching between input sources. Manual Setup > Input Select > input source (DVD, etc. ) > Volume Trim > Control range: ­6. 0 dB to +6. 0 dB Audio Select Decoder Mode Volume Trim 0. 0dB I/O Assignment Audio Select Decoder Mode Volume Trim Rename V-AUX Audio Select Decoder Mode Volume Trim Rename Volume Trim Multi CH Assign Rename MULTI CH Note You can only adjust the volume for the current input source using this setting. 1 Set AMP/SOURCE/TV to AMP and then press GUI TOP on the remote control. ADVANCED OPERATION AMP GUI TOP SOURCE TV TITLE BAND Stereo/Surround Input Select Manual Setup Auto Setup System Memory Sound Video Basic Option English 73 SYSTEM OPTIONS Rename (Rename) Use this feature to change the name of the inputs in the GUI or the front panel display menu. (DVD is used as the source component in the following example. ) Input Select > input source (DVD, etc. ) > Rename I/O Assignment (Input/output assignment) You can assign the digital audio input/output and component video jacks to other components if this unit's initial settings do not correspond to your needs. Change the following parameters to reassign the jacks and effectively connect more components. Once the jacks are reassigned, you can select the corresponding component using the INPUT selector on the front panel or the input selector buttons on the remote control. Input Select > input source (DVD, etc. ) > I/O Assignment > Example 1: To assign the COAXIAL 7 (CD) jack to the DVD input. 1) Select Input Select and then select DVD. 2) Select I/O Assignment > Coaxial Input and then select 7 CD. 1) Select Input Select and then select the input source (DVD, etc. ). 2) Select I/O Assignment and then select the jack assignment (Coaxial Input, Optical Input, Optical Output, Component Video, or HDMI). 3) Select NONE and then press ENTER to clear the assignment. Optical Output Component Video I/O Assignment Audio Select Decoder Mode HDMI 1 2 Press an input selector button to select the input you want to change the name of. Press l / h to place the _ (under-bar) under the space or character you want to edit. Decoder Mode Volume Trim Rename CAPITAL DVD OK RESET 3 4 Press ENTER to select a character type (CAPITAL/SMALL/FIGURE/MARK). Press k / n to select the character you want to use and l / h to move to the next one. · You can use up to 8 characters for each input. · Press n to change the character in the following order, or press k to go in the reverse order. Press ENTER to switch between character types: CAPITAL A to Z, space SMALL a to z, space FIGURE 0 to 9, space MARK !, #, %, &, etc. · Repeat steps 1 to 3 to rename each input. [. . . ] AC 110/120/220/230­240 V, 50/60 Hz [China model] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V, 50 Hz [Korea model] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V, 60 Hz [Australia model] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . and Europe models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]