User manual YAMAHA RX-V393RDS

[. . . ] GB RXV493RDS RXV393RDS Natural Sound AV Receiver Récepteur audiovisuel "Son Naturel" Natural Sound AV-Receiver Natural Sound AV-receiver Sintonizzatore AV a suono naturale Receptor AV de Sonido Natural Natural Sound AV Ontvanger OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS MITGELIEFERTE ZUBEHÖRTEILE MEDFÖLJANDE TILLBEHÖR ACCESSORI IN DOTAZIONE ACCESORIOS INCLUIDOS BIJGELEVERDE ACCESSOIRES Indoor FM Antenna Antenne FM intérieure UKW-Innenantenne FM inomhusantenn Antenna FM interna Antena FM interior FM Binnenantenne q q q q q q q After unpacking, check that the following parts are included. Après le déballage, vérifier que les pièces suivantes sont incluses. Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. Kontrollera efter det apparaten packats upp att följande delar finns med. [. . . ] (Refer to page 39. ) * The name of the selected input source will appear on the display. 4 Select the main speakers to be used. SPEAKERS A B Notes on using the input selector buttons Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. q The selection of TAPE/MD MONITOR (MON) cannot be canceled by pressing another input selector button. To cancel it, press TAPE/MD MONITOR (MON) again so that the "TAPE MON" indicator disappears from the display. When you select a button other than TAPE/MD MONITOR (MON), make sure that the "TAPE MON" indicator is not illuminated on the display. q If you select the input selector button for a video source without canceling the selection of TAPE/MD MONITOR (MON), the playback result will be the video image from the video source and the sound from the audio tape (or MD etc. ). q Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. q ON OFF * If you use two main speaker systems, press both the A and B switches. When you finish using this unit Press the STANDBY/ON switch on the front panel again or the POWER /I key on the remote control transmitter to turn this unit into the standby mode. 25 To listen to a decoded source using Dolby Digital (AC-3) or DTS by reproducing the signals input to the 6CH DISCRETE INPUT terminals of this unit. In step 3, press the button (shown below) once or more so that "6ch" appears on the display. Discrete signals from the unit connected to the 6CH DISCRETE INPUT terminals of this unit are selected as the input signals. To cancel listening to a decoded source using Dolby Digital (AC-3) or DTS Press the same button again or select another input source. Note for reproducing discrete signals with Dolby Digital (AC-3) or DTS decoded: 1. Your speaker system must include a center speaker. Your speaker system must include a subwoofer. * Connect a subwoofer which has a built-in amplifier to the SUBWOOFER OUTPUT terminal of this unit. If you do so, you should make a setting for distributing signals at the LFE channel to the right and left MAIN output terminals on the Dolby Digital (AC-3) Decoder etc. For details, refer to the owner's manual for the Dolby Digital (AC-3) Decoder etc. Notes q When you switch to the "6ch" mode, the built-in Digital Sound Field processor will not work and adjustment of delay time cannot be made. q RX-V493RDS TV/DBS DVD/LD TV/DBS DVD/LD or TAPE/MD MON 2CH/6CH TAPE/MD MON 2CH/6CH RX-V393RDS VCR VIDEO Switching this unit to the "6ch" mode will input no signal to this unit if there is no connection to the 6CH DISCRETE INPUT terminals of this unit. 2CH/6CH 26 English TO RECORD A SOURCE TO TAPE (OR MD) RX-V493RDS RX-V393RDS 14 28 40 2 l6 20 l2 8 4 4 12 l6 20 l2 28 8 40 4 60 2 60 2 0 ­dB ­dB 0 1 Select the source to be recorded. 3 CD Begin recording on the tape deck (or MD recorder etc. ) or VCR connected to this unit. If the tape deck (or MD recorder etc. ) is used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MONITOR (MON) so that the "TAPE MON" indicator lights up on the display. RX-V393RDS DVD/LD TUNER PHONO 4 2 RX-V493RDS Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 29. ) VOLUME TAPE/MD MON l6 20 l2 TV/DBS TAPE/MD MONITOR VCR 2CH/6CH 28 8 PHONO CD TUNER PHONO 40 4 60 2 0 ­dB Notes The settings of DSP and the VOLUME, BASS, TREBLE and BALANCE controls have no effect on the material being recorded. q In step 1, do not make an input source selection so that "6ch" appears on the display. Signals input to this unit's 6CH DISCRETE INPUT terminals cannot be recorded by a tape deck, MD recorder or VCR. q 27 Selecting the SPEAKER system Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. SPEAKERS A B Adjusting the BASS and TREBLE controls BASS 0 l 2 3 4 5 5 2 3 4 5 5 TREBLE 0 l l 2 3 4 l 2 3 4 ON OFF BASS : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. BALANCE 0 l l 2 3 4 L5 2 3 4 5R TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Note These controls are effective only for the sound from the main speakers. Note This control is effective only for the sound from the main speakers. RX-V493RDS only Adjusting the subwoofer output level RX-V493 only If your audio system includes a subwoofer, and an amplifier driving the subwoofer (or a subwoofer system including an amplifier) is connected to the SUBWOOFER OUTPUT terminal on the rear of this unit, you can adjust the subwoofer output level on this unit. 1 Press once or more so that "SWFR" appears on the display. DELAY/CENTER /REAR/SWFR 2 By continuously pressing the "+" or "­" side of the TIME/LEVEL button, the level value changes continuously. If you feel that bass tone is insufficient, increase the level, and if you feel that bass tone is overly emphasized, decrease the level. TIME/LEVEL Adjustable Control range: MIN, ­20 to 0 dB 28 English TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). l6 20 l2 28 8 40 4 60 2 0 ­dB 12 AUTOMATIC TUNING 43 1 Select "TUNER" as the input source. TUNER PHONO CD MANUAL TUNING 1 Select "TUNER" as the input source. TUNER PHONO CD 2 Select the reception band (FM or AM) confirming it on the display. FM/AM 2 Select the reception band (FM or AM) confirming it on the display. FM/AM or or 3 TUNING MODE 3 AUTO TUNING MODE AUTO/MAN'L MONO AUTO/MAN'L MONO Turn the "AUTO" indicator off. 4 To tune to a higher frequency, press the right side once. [. . . ] There are buzzing and whining noises (especially in the evening). Noises will result from ligtning, fluorescent lamps, motors, thermostats and other electrical equipment. Direct sunlight or lighting (of an inverter type of fluorescent lamp etc. ) is striking the remote control sensor of the main unit. The batteries of this remote control transmitter are too weak. Remote control transmitter The remote control transmitter does not work. Replace the batteries with new ones. Turn the power to this unit on. The sound is degraded when listening with the headphones connected to the compact disc player or cassette deck that are connected with this unit. Others This unit is in the standby mode. 43 SPECIFICATIONS AUDIO SECTION Minimum RMS Output Power per Channel (Power Amp. [. . . ]